£55.00 exc vat
£66.00 inc vat
now
£46.75 exc vat
£56.10 inc vat
In stock
£55.00 exc vat
£66.00 inc vat
now
£46.75 exc vat
£56.10 inc vat
In stockRecommended usage 1 x CZH149 to fit one mini.
The only bonnet landing panel available for the clubman shape body for a long time this part is perfect in every detail and was used on the heritage bodyshells.
A Genuine panel is now available from BL Heritage CZH149.
...
Available again from genuine tooling
Fits all mini clubmans only. There is no aftermarket version available of this bonnet anymore.
this bonnet MUST use the later 1981 onwards BMP348 / BMP349 hinges
the vertical panel that sits between the bonnet slam panel (MS149) and the front panel on clubmans only
For vans and pickups this had later type hinge positions 1.25" from the edge as per the saloon but did not have the extra lip for the bonnet upper grille moulding which was never fitted as standard---Mk1/2 variants had the hinges in a different posit...
When they introduced negative earth sytems for the MK3 cars they had to put these stickers on the cars to warn people as all previous models were positive earth which caused havoc with people trying to fit radios and other electrical equipment with t...
Genuine version of 14A8347.
Genuine version of 14A8346.
The half bowl for holding original sealed beams into the headlamp bowl om minis and many other headlamps of the 60s and 70s. Sold singly 2 required per car.
This kit contains all the brackets and mounts required for fitting Minis with 10/12" wheels or with 145 profile tyres.
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres and 5.5 gallon tank se...
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
Upgraded L/H "A" panel for all Minis with internal hinges,1970 on.
A single wall panel has has a tendency to develop rust spots and is probably one of the most common panels replaced on the Mini.
Only available from Mini Spares th...
Upgraded R/H "A" panel for all Minis with internal hinges,1970 on.
A single wall panel has has a tendency to develop rust spots and is probably one of the most common panels replaced on the Mini.
Only available from Mini Spares th...
Mk3 on Mini (all internal hinged models) inner door frame bottom drain hole repair section with outer skin lip for the R/H door, had 3 drain holes also see part number MS34L for the repair for the bottom of the door.
Technicall...
Mk3 on Mini (all internal hinged models) inner door frame bottom drain hole repair section with outer skin lip for the L/H door, also see part number MS34L for the repair for the bottom of the door.
Technically you cannot fit b...
Really a built up half front end for the mini clubman, consists of a lower panel with headlamp panels,slam panel and stiffener between the front and slam panel. 76 ON--no inner or outer wings
In 1993 the moulding between the wheel arches was changed from black plastic to rubber and was still used on twin point rubber arches. This is the Minispares version which is a slightly more rounded profile.
The left side inner fender of the Mini Clubman should have a metal cowling to focus the air from the radiator to the wheel well. The almost sqaure cowling is spot welded to the inner fender. If you are resoting your car properly you will need to ha...
Non genuine R/H repair section
for wind up window type doors this is the lower 2-3" of the inner skin and the bottom of the door section that usually rusts out-includes a lip section where the outer skin flaps overlaps for fitment--new panel...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.