PANEL HINGE INNER L/H A PANEL EXTERNAL HINGE TYPE
14A8347GEN

£70.00 exc vat

£84.00 inc vat

now

£64.40 exc vat

£77.28 inc vat

In stockIn stock
Genuine version of 14A8347.

£70.00 exc vat

£84.00 inc vat

now

£64.40 exc vat

£77.28 inc vat

In stockIn stock

Recommended usage 1 x 14A8347GEN to fit one mini.

Alternative products

For minis with sliding windows and external door hinges.

This is the inner hinge panel with the brackets on to reinforce the areas where the hinges sit. You will require the outer panel also 14A6901 for R/H and 14A6902<...

People also bought products

If you fit 13" wheels and need to cut the wings away for clearance these are the reinforcements strips Rover used on the cars with Sportspack arches.

see Downloads on web site for diagrams on where to cut wings and A panels under part number...

For Minis with sliding windows and external door hinges These genuine R/H outer A panels fit over the extra inner panel which have brackets on to reinforce the exterior hinges. If the outside one is rotten you can guarantee the i...

For minis with sliding windows and external door hinges.

This is the inner hinge panel with the brackets on to reinforce the areas where the hinges sit. You will require the outer panel also 14A6901 for R/H and 14A6902<...

Genuine door hinge panel L/H for all MK3 Minis with internal hinges and doors that have wind up windows. Although it is a single wall panel it still has a tendency to develop rust spots so the trade prefer the best fitting thicker upgraded [link]ALA5...

Genuine door hinge panel R/H for all Minis with internal hinges and doors that have wind up windows. Although it is a single wall panel it still has a tendency to develop rust spots but a slightly thicker upgraded panel the local bodyshops love is [l...

For minis with sliding windows and external door hinges.

This is the inner hinge panel with the brackets on to reinforce the areas where the hinges sit. You will require the outer panel also 14A6901 for R/H and 14A6902<...

For Minis with sliding windows and external door hinges These genuine L/H outer A panels fit over the extra inner panel which have brackets on to reinforce the exterior hinges. If the outside one is rotten you can guarantee the i...

Genuine L/H rear quarter outer skin from the B post back for MK1/2 cars with sliding windows.

Crossmember at the back of the engine bay where the master cylinders fit, fits MK1/2 models.



correct shape for a mark one unlike the laster version that is modified for carb clearance

Genuine R/H rear quarter outer skin from the B post back for MK1/2 cars with sliding windows.

MK1 front bulkhead skin to suit mk1 with the round hole for the heater trunk pipe. Bonnet hinge brackets not fitted.



Can be used in later models with some adaption.

Rear subframe mounting stiffener L/H repair bracket with holes for subframe mounting and attaches to wheel arch Fits on ALA8623

Rear subframe mounting stiffener panel R/H with holes for subframe mounting to wheel arch. Sits on ALA5524 or ALA5528

Floor pan for Mini van/estate with no x member for remote change gearbox. Non Genuine. For saloon see 14A6491

picture is just to show what you get but bulge on centre tunnel for starter button appears to be on wrong side as this...

Van roof panel for post 1966 cars, these are without vent piercing.

Non genuine but the only panel available.

This is small plate that welds into the later lower dash rails to convert them to mk1 size for people who want early switches in a late car.

Non Genuine L/H lamp repair panel for rear corner panel on the Mini Pick-Up.

The top rear capping panel is also available as 14A7558CAP