BULKHEAD PANEL MK1 WITH AIR VENT HOLE
14A9563MS

£112.50 exc vat

£135.00 inc vat

In stockIn stock
MK1 front bulkhead skin to suit mk1 with the round hole for the heater trunk pipe. Bonnet hinge brackets not fitted.



Can be used in later models with some adaption.

£112.50 exc vat

£135.00 inc vat

In stockIn stock

Recommended usage 1 x 14A9563MS to fit one mini.

People also bought products

Crossmember at the back of the engine bay where the master cylinders fit, fits MK1/2 models.



correct shape for a mark one unlike the laster version that is modified for carb clearance

Repair section of bottom of door for external hinge cars, MK1/2.

This crude non genuine parts is the only repair section available for early doors apart from door skins.Lots of stretch marks and wrinkles but they have been fitted by customer...

Repair section of bottom of R/H door for external hinge cars, MK1/2.

this crude non genuine parts is the only repair section available for early doors apart from door skins. Lots of stretch marks and wrinkles but they have been fitted by cus...

Small bracket under the front bumper lip to hold the number plate, sold singly.

For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to.This is the left hand pane wing with radiator vent slats but not ...

For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to. This is the right hand panel made by Heritage but not 100% perfe...

non genuine oversill MK1/2 van floor profile R/H with 4 flute vents

see MS58R for 6 flute type side, wide type

2-3" lower section of Van body section

from A post to rear wheel arch including the vital door step sill profile that rusts plus the horizontal edge that the chrome trim sits on-for cars with hinge tye doors

Genuine L/H rear quarter outer skin from the B post back for 1970 on wind up window door cars only.From below the rear side window down, including the lip that the rear quarter light window seal sits on but does not include the inner stifener waist r...

rear subframe mounting stiffener L/H repair bracket with holes for subframe mounting and attaches to wheel arch Fits on ALA8623

THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7

This panel has mounting holes for later models facia crash panel. These holes will require blanking for true originality on earlier models without the facia pad

non genuine oversill MK1/2 van floor profile L/H with 4 flute vents see MS58L for 6 flute vents

Front number plate to the old original classic size 3.75"high by about 20.5"long overall. If you prefer a stainless steel plate to the later current legal size see 8B12390 which is 5.5" high and one inch longer

Closing plate against the bodyside in the base of the l/h rear companion/glove box now has a square pressing hole for later models

Rear subframe mounting stiffener panel R/H with holes for subframe mounting to wheel arch. Sits on ALA5524 or ALA5528

Non genuine rear valance closing panel R/H for saloon cars only. Similar to ALA5528 but less panel with 2 holes for mounting rear subframe and 14A6609 floor to wheel arch reinforcement.

Genuine panel that has the holes for wipers and jets with only a few inches of pillar which is basically the area that rots. Also referred to as the windscreen scuttle lower panel. Fitting the genuine type ensures you should get a better windscreen a...

Genuine R/H rear quarter outer skin from the B post back for MK3 cars with wind up windows.From below the rear side window down, including the lip that the rear quarter light window seal sits on but does not include the inner stifener waist rail [lin...