£8.00 exc vat
£9.60 inc vat
In stock
£8.00 exc vat
£9.60 inc vat
In stockRecommended usage 2 x 14A8456 to fit one mini.
The front bumper of your Mini should be mounted to this simple 'L' bracket that should in turn be spot welded to the lower edge of your nose panel. Not only is this often damaged in accidents but it also was often removed during modification cycle b...
Crossmember at the back of the engine bay where the master cylinders fit, fits MK1/2 models.
correct shape for a mark one unlike the laster version that is modified for carb clearance
MK1 front bulkhead skin to suit mk1 with the round hole for the heater trunk pipe. Bonnet hinge brackets not fitted.
Can be used in later models with some adaption.
Non Genuine for the Pick-up and Van 1961-64 with a slat type fixed grille as a trademark for Mini commercial type vehicles originality.
Usually ordered for customers requirements as these are very rare models.
This panel has no b...
ADAPTOR PANEL TO CONVERT LATER FRONT PANELS TO THE PRE 1964 FULL SKIRT FRONT PANEL.
ADAPTOR PANEL TO CONVERT LATER FRONT PANELS TO THE PRE 1964 FULL SKIRT FRONT PANEL.
Slat type front grille section for mini van which will need trimming before welding into recess of either an original damaged front panel or a saloon version.
It is sold as a grille size panel and can be fitted as such when painted with [li...
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to.This is the left hand pane wing with radiator vent slats but not ...
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to. This is the right hand panel made by Heritage but not 100% perfe...
Aftermarket version of the L/H floorpan for 1991 on cars.
This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 199...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
1970 on, cars with internal hinges and wind up windows
This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section of inner wing
1970 on, cars with internal hinges and wind up windows
This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
floor pan front to rear for the left hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mul...
Floor pan front to rear for the right hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mult...
Front number plate to the old original classic size 3.75"high by about 20.5"long overall. If you prefer a stainless steel plate to the later current legal size see 8B12390 which is 5.5" high and one inch longer
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.