£20.40 exc vat
£24.48 inc vat
In stock
With a headlamp rim fixing bracket 37H7421 attached
Whether you are doing a full restoration, collision, or rust repairs, the job is much easier and more pleasant when you use clean new parts. There is nothing special about these headlamp buckets, they are just new!
Sold singly,2 per car required
£20.40 exc vat
£24.48 inc vat
In stockRecommended usage 2 x MS14 to fit one mini.
Headlamp sundries kit.
Includes two adjuster screws, plastic nutserts, pullback spring. Two kits are required per car.
The headlamp bucket is isolated from the body with these rubber seals/gaskets.
The half bowl for holding original sealed beams into the headlamp bowl om minis and many other headlamps of the 60s and 70s. Sold singly 2 required per car.
Pop rivet for fixing the headlamp bowl to the wing. Great for MS14 metal bowl but be careful if using on plastic bowls
This plastic bowl kit includes the inner rim to hold your light unit and will obviously not rust like the old originals. You will need a headlamp outer rim so why not fit our own developed stainless steel variety which is cheaper than even chrome bud...
Although this panel is non genuine it is the most accurate for MK1 Cooper S restorations as it has the correct number plate brackets and slam panel.
If you have a pre 1964 car with the one piece valance with no cooling cut outs for brakes ...
Pop rivet for fixing the headlamp bowl to the wing. Great for MS14 metal bowl but be careful if using on plastic bowls
Gasket/seal for all 1997 on mpi headlamp bowls (self levelling type).
Non genuine but a correct replica part for all pre 1964 cars with a full skirt lower front valance panel without cooling cut outs on the corners which was introdeced in 1964 to help drum brakes cool and be more efficient
A single plastic headlamp bowl only, to accept the levelling motor and rim for all twin point (1997 onwards) Minis plus some export SPI models.
Slat type front grille section for mini van which will need trimming before welding into recess of either an original damaged front panel or a saloon version.
It is sold as a grille size panel and can be fitted as such when painted with [li...
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Reproduction version os ASJ360070. For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet fittings.
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to.This is the left hand pane wing with radiator vent slats but not ...
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to. This is the right hand panel made by Heritage but not 100% perfe...
For wipac quadoptics-replacement bulb holder for lamps also supplied in kit.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. The halogen headlamps have very bright 55/60 watt bulbs. Their special lens gives g...
Commercial Mini floor extension
It is an essential part for the correct restoration of all the longer wheelbase mini derivatives. From the original tooling.
The best chrome type available with screw and washer.
A headlight trim ring is only the starting point of a good looking car, but you have to start somewhere. Sold singly 2 required per car. These are the original type chrome over solid bras...
genuine front panel for the mini clubman before 1976 when the subframe was rubber mounted.see AAM1022 for rubber mounted type as fitted from 1976 on.
the front of these panels is the same but the subframe mounting bracket on the...
The only bonnet landing panel available for the clubman shape body for a long time this part is perfect in every detail and was used on the heritage bodyshells.
A Genuine panel is now available from BL Heritage CZH149.
...
These are for Left had drive L/H/D. See S4698B for Right hand drive R/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special...
These are R/H/Drive, see S4699B for L/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special lens gives good long range visi...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.