£225.60 exc vat
£270.72 inc vat
In stock
See EVOLUTION001 FOR GREAT ALTERNATIVE CAM
As of July 2007 Kent cams have no supply of old camshafts for reprofiling and now only supply camshafts from new blanks.
£225.60 exc vat
£270.72 inc vat
In stockRecommended usage 1 x MDM286 to fit one mini.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
A vital aid for accurate valve timing this disc is a 360 degree protractor disc made by kent cams.
Genuine Mini Spares camshaft,great for all road uses- A Plus slot drive only.
Valve clearance should be 0.014" on inlet and 0.016" exhaust. LCA 107 degree
DURATION INLET 264 EXHAUST 268, LIFT INLET 264 EXHAUST 289.
This ca...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
full race cam in A plus drive with power band from 4000-8500 with cam lift of .340 --see catalogue for full specification.
As of July 2007 Kent cams have no supply of old camshafts for reprofiling and nowonc will only supply camshafts from n...
woodruff key to fit in the camshaft to hold the larger timing chain gear. See 6K836 for the crankshaft keyway for the lower smaller timing chain gear
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
The only upgrade in camshaft you can get away with on the single point injection cars without changing ECU etc--A mild road cam
As of July 2007 Kent cams have no supply of old camshafts for reprofiling and we will only supply camshafts fro...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Slightly lumpy at idle, especially in small bore units. Strong mid and top end power. Rev band 1,500 - 7,000 rpm.
As of July 2007 Kent cams had no supply of old camshafts for reprofiling and now only supply camshafts from new blanks.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
Lightened cam gear duplex timing gear and chain set. Not recommended for race/rally applications. approx 69-70g 9% lighter
General: Camshaft Drive Systems
For highly tuned engines always use steel duplex as cast is nowhere as st...
Genuine camshft,Unique to MPI-has a very distinguishable twin prong lobe for the Twin point injection pick up and is therefore unique to this model only. Distributor drive usually machined off.
alternative mild tune camshaft is available [li...
Standard weight, 44.00grams, follower with oil drain hole. Always check for wear and replace whenever a new camshaft is fitted. These are manufactured by the supplier to AE Hepolite the original engine components manufacturer and should be coated wit...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
Needs free flowing exhaust manifold and system, high CR, best with medium to long inlet manifolds. Mid and top end power only. Gives very good results when twin SU’s have to be used. Rev range 3,250-8,000/8,500 dependent on build.
As of J...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.