£287.40 exc vat
£344.88 inc vat
In stock
As of J...
£287.40 exc vat
£344.88 inc vat
In stockRecommended usage 1 x MDM296 to fit one mini.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
A vital aid for accurate valve timing this disc is a 360 degree protractor disc made by kent cams.
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
"Scatter Pattern" cams were designed by David Vizard to work best with the pecularities of the A-Series' siamese intake ports. The 310 scatter pattern is the ultimate race cam. Needs fully prepared engine for good results - high CR, high flow head, ...
Hottest road usable cam. Not a good traffic cam. Lumpy idle. Not very suitable for small bore units unless fully prepared with big valve head. Very strong mid and top end power. Rev range 2,000 - 7,500 rpm.
See EVOLUTION001...
Slightly lumpy at idle, especially in small bore units. Strong mid and top end power. Rev band 1,500 - 7,000 rpm.
As of July 2007 Kent cams had no supply of old camshafts for reprofiling and now only supply camshafts from new blanks.
Standard weight, 44.00grams, follower with oil drain hole. Always check for wear and replace whenever a new camshaft is fitted. These are manufactured by the supplier to AE Hepolite the original engine components manufacturer and should be coated wit...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
Adjustable cam gear set with non stretch chain. Cam gear weighs 674g
Even a stock camshaft needs to be timed correctly. If you want to get the maximum benefit from a "hot" cam it is doubly important that the cam timing be correct. This adju...
Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.
This chain saves all the time and effort requ...
Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.
Spin on oil filter housing for performance engines-uses 88G402 gasket-made out of billet alloy it has a strong mating face to the block where oil leakage occurs from high revving engine vibrations, is slightly shorter offering more clear...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. Vandervell, once the only bearings to use on a competition motor they are now made by Mahle. ACL is now commonly used in race engines.
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...
Low drag 1275 piston standard size 2.780 (Rings included).
This piston has a possible compression ratio of 10.3:1 as fitted to Cooper RSP 1990.
The best performance 1275 pistons are C-STN100 range which have 9.73cr when the piston i...
3mm OIL RING with compression ring size .0591" (1.5mm)and one piece oil ring .1181" (3mm)on p21253 pistons giving 9.7cr on 1275cc. std ring size
For performance see steel ring set with 3 piece oil ring as favoured by engine builders[link]C1...
Absolutely prevents the engine from rocking! These should NEVER be used on a street car BUT it could also be said that every serious race car should have them. Our newest design includes captive nuts for ease of installation.
sold ...
This kit includes a new oil galery plug with an adjustable knob and a washer which is used as a spring seat in the plug against the relief spring. This makes a playform for the adjuster bolt to adjust the engine oil pressure. Winding the knob in incr...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.