POLISHED ALLOY DOOR PULL HANDLES - PAIR
MSA1132

£13.02 exc vat

£15.62 inc vat

In stockIn stock
High quality, polished alloy door pull handles.

These aluminum handles will wind up window cars and they won't snap off like the original plastic ones

For matching window winders see MSA1130.

See MSA1129 for complete car set

£13.02 exc vat

£15.62 inc vat

In stockIn stock

Recommended usage 1 x MSA1132 to fit one mini.
Wind up Window Doors - Qty 1

Kit products

This kit contains MSA1130/MSA1131/MSA1132 as a car set of TOP QUALITY polished alloy interior door handles.

People also bought products

This plastic handle fitted any wind up window cars up to the introduction of the twin points, which then changed and the handle fitted from 1996 on is now obsolete.

MK1/2 interior door handle with screw and washer.

This solid "spoon" handle is brittle and easily broken.

These are the original shape as sold under the Unipart label, not the later Rover bagged item which was a reproduction with d...

Uses ADU8081 screw and YXX3200PA cover. With a spring loasded winder knob this handle was fitted to later cars as a safety requirement. Fitment was from 1983 but fully introduced in 1984

Metal chromed old type classic handle revived for use on MG variants and then a fashion item on minis. On later cars CMZ312 screw might be required which has a smaller diameter head and longer thread. Length 90mm.

High quality, these handles fit all models with windup windows.



For matching door opening handles and bezel, see MSA1131/MSA1135.

See MSA1129 kit for car set of plain alloy polished handles.

Fitted on cars up to about 1982 approximately before spring type knob on handle was introduced for safety homologation YXX3199PA.

The screw this CZA7109 handle is ZKC3317.

This 10 piece handle set is exactly the same kit as sold by every other mini specialist is in bright alloy (not polished alloy as per our other superior kit MSA1129) and consists of two of each of the following, door openers, window winders and their...

High quality, these polished door opening handles will fit all models with windup windows.

For matching window winders see MSA1130.

See MSA1129 for complete car set

The chrome moulding to fit the door bin on all sliding type window doors, MK1/2 and all vans/pickups. See 14A6879 for early cars with lug ends held on by screws

Use the correct single sided prong clips only ADH3809 ...

This plastic handle fitted any wind up window cars up to the introduction of the twin points, which then changed and the handle fitted from 1996 on is now obsolete.

If you drive your MINI/MGB often then you know that the standard plastic window winder handles are prone to breaking. These chrome metal handles are somewhat stronger and look great alongside the other chrome trim in the car's interior. Next time ...

plastic bezel that sits behind window winder handle.

door cappings in Burr walnut to compliment the wooden dashes

See also MSA0193 door opening handles, MSA0192 door opening handles and MSA0194 window winder handles

Plain white with white backing aftermarket sun visor as fitted to Mk3 models 1977-92 which were thinner than Mk1 for safety crushing requirements. Although not standard for earlier models will fit cars from December 1965. Check out the special clips ...

One pair (saloon car set) of rear quarter door cards in black , 1976 - 1980

Cream colour crackle finish sun visor as fitted from december 1965 onwards. Will fit later cars if required. Drivers side without mirror.Check out the special clips to hold these visors as they are sold seperately in car sets only as SV2021<...

Black with mirror, optional colour aftermarket sun visor for Mk3 models which were thinner than pre 1965 cars for safety requirements. Will fit cars from December 1965 on. Check out the special clips to hold these visors as they are sold seperately ...