£258.33 exc vat
£310.00 inc vat
£258.33 exc vat
£310.00 inc vat
Recommended usage 1 x MSSK1008 to fit one mini.
This plastic clip was commonly used by Rover for all car trimming and first found its way on the wind up window version mini door panel.9 per side but always purchase a spare in case of breakages.
Reinforced elastomer liner for door trim made from VELVEX to prolong the life of your door cards.Die cut on press tools that make the original door cards. Each hole for door locks, window winders, door handles, speaker holes are precision cut to fit ...
Mk1/2 style pattern door and rear quarter grey vinyl trim kit
These are the 4 major parts that can give your car a fresh look- only fits wind up widow type doors as fitted to MK3 range mid 1973 , without ash tray facility in rear glove box
Our lightweight underfelt kit is the perfect companion when fitting a new headlining. Made from lightweight felt and cut to size, this fits into the cavity of the roof before fitting your new headlining and provides increased sound insulation and pro...
Complete car set of roof lining rods, comprising of 1 Red, 2 White, 1 Black, 1 Blue and 1 Yellow
number 1 with red ends is EEB100060
number 2 and 3 is white ends are both EEB100070
number 4 with black ends is EEB100080
...
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
The rubber type grip fitted on handbrakes-
will fit any single cable hand brake from 1976 on
Mk1/2 used 13H5541 thinner plastic type--to fit this to pre 1976 early cars you will need to put lots of sticky tape on the h...
High quality, polished alloy door pull handles.
These aluminum handles will wind up window cars and they won't snap off like the original plastic ones
For matching window winders see MSA1130.
See MSA1129 for...
Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.
Also suitable for Twin Point indicator fixings.
127cm long and 43cm wide this is enough leather cloth trim that fitted S and deluxe models on the upper and lower facia plus the winscreen A posts. Fitting instructions are included but no glue.
The metal retainer that holds the rod change gear lever gaiter CZH4278 in place
Fitted 1969-77 and 1992-96 originally and white from 1970-96 so see PAM5401BLACK and PAM5401AP. C posts trims changed with MPI or Heritage shells.
These headlinings are held in by different shape/length rods which a...
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
Metal chromed old type classic handle revived for use on MG variants and then a fashion item on minis. On later cars CMZ312 screw might be required which has a smaller diameter head and longer thread. Length 90mm.
Favourite old ashtray for MK1/2 minis with the fluted top for the rear glovebox and facia. Fitted to minis with painted top dash rail from 1959-85.
See 24A1538 also for flat lid version as fitted when top dash rail is vinyl cove...
Union Jack stick on logo for use on gearlever knobs and key fobs sold by us.
About 27.4mm wide.
Fire retardent felt with correct cut outs for MK3 cars for the mini firewall just behind the carb and air cleaner full width of the panel see FELT860 for spray adhesive.
This 10 piece handle set is exactly the same kit as sold by every other mini specialist is in bright alloy (not polished alloy as per our other superior kit MSA1129) and consists of two of each of the following, door openers, window winders and their...
Front Ashtray with Solid top as used in the top dash rail when vinyl covered, from 1961-71, Most deluxe and Cooper variants. See 8D2490 for fluted ash tray as fitted to painted top dash rail 1959-85
OEM firewall soundproof. These OEM style soundproof mats will fit right on any MkI/MKII Mini. Cutouts are there for the fresh air hose, hinges, wiring and wiper motor. The felt/jute is flame resistant on one side. You will notice the difference!
A reproduction of the original MK1 steering column plastic shroud, moulded in the original plastic, painted and ready for polishing! Sold only in sets of upper and lower pieces. For MK2 see 8G6035.