£178.83 exc vat
£214.60 inc vat
Out of stock
Our kit has the following components. pairs of door panels and rear quarter panels, rear pocket liners, wheel arch covers, and one rear parcel shelf liner. A 13 piece kit is available with oval dash liners for original Cooper S or deluxe cars with the central speedo and 2 gauges. See TK3007A
£178.83 exc vat
£214.60 inc vat
Out of stock
Reinforced elastomer liner for door trim made from VELVEX to prolong the life of your door cards.Die cut on press tools that make the original door cards. Each hole for door locks, window winders, door handles, speaker holes are precision cut to fit ...
MK3 door hinge fitting kit for all internal hinged doors. (hinges not included)
Called the rear bonnet seal it actually sits in the windscreen front scuttle panel on all minis up to 1991. This is the shape and size neoprene foam seal that we have found works best and has an adhesive backing to make fitting easier and less messy.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
This is the crossmember for the dash at the back of the engine bay which holds the master cylinders. When fitting to Clubmans extra end pieces are required. Fits 1976 on but does not have PDWA valve bracket. The original Rover parts are supplied with...
Car set (one pair) rear wheel arch vinyl trim covers.
Original MK1/2 finer grain wheel arch cover-heavier grain pattern is WAC3025A although not much diffferent and never noticed.
127cm long and 43cm wide this is enough leather cloth trim that fitted S and deluxe models on the upper and lower facia plus the winscreen A posts. Fitting instructions are included but no glue.
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
Draft excluder for sliding window doors as fitted to Mk1/2 Minis. Right hand side. Properly cut angles as original.Either crimp both ends with your fingers to make it stay on door glass or use a glue as per the factory on later vans.
Qty one...
Moulded black carpet set for Rod change change with soundproofing attached where appropiate.
These fit correctly and snugly in your car over the tunnels etc for that professional look. 2 rubber front foot pads and on rear carpet has reinforc...
This 10 piece handle set is exactly the same kit as sold by every other mini specialist is in bright alloy (not polished alloy as per our other superior kit MSA1129) and consists of two of each of the following, door openers, window winders and their...
These are the clips that hold on the vertical seam mouldings on all minis.
The original metal type are prone to rust so Mini spares producedd these stainless steel versions which are also cheaper. Supplied as a single clip, order as many as ...
Black painted liners for deluxe cars with air vents and central speedo and 2 gauges.
Mkl Mini door seals were unique in both shape and texture, they had a natural rubber finish and a pronounced point on the sealing edge. These are the only seals that should be used on sliding window cars. Later seals are too big and place undue stres...
These screws fit the lower 2 holes on all boot hinges.Also see 24A2175/6 gaskets
that you will need. 1/4" unf 5/8"long, also for tailgate stays on pickup.
BEZEL for mk2 on switch panel.
this item is satin finished, though can be polished by customer if required
These pads were used by Rover to help deaden the sound in a mini. Fitted to the door, rear quarter panel and roof panel behind the trim, they stick on.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.