£59.58 exc vat
£71.50 inc vat
Out of stock
£59.58 exc vat
£71.50 inc vat
Out of stock
Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...
Mini Spares Non genuine timing chain gasket fitted to every BMC A series engine with 10 gasket holes until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.
Gasket material h...
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
Emission hose from carb to breather valve, this hose has special size ends and made of a material to cope with taking these emission gases.
Approx 23.75" long with internal 5/16" end and 1/2" other end.
GHC406 jubilee c...
Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S
( Tri-Metal )
Sintered copper lead, lead plated,steel backed
Nominal Composition
Copper 74%
Lead 24%
Tin ...
Mini Spares own Universal gasket set for solid wall blocks
For any manual block, includes gaskets for "A"Plus and pre A Plus timing covers, but is less tappet chest cover gaskets. Does not include clutch oil seal.
We now offer an en...
Original equipment quality for factory built engines giving longer life expectancy on road cars under variable conditions of oil and use. These are the 1275cc mains as fitted to A Plus engines with the locating tab in the middle rather than to the ou...
Engine front plate gasket for any A series units pre A Plus.
For A plus see GUG705554GM or CAM4700B.
For a superb quality engine block gasket set see GUG701614CS
Universal paper oil pump gasket for all A series engines. Fits between pump and block. See GUG705560GM for genuine.
Plastic tensioner pad to take up the slack in single row timing chains on A plus engines that wears and should be replaced nearly every time you have the timing cover off. From engine numbers 99H791/10H791 AND ALL A+. Fitted to 998/1100cc from 1979 a...
This kit includes a new oil galery plug with an adjustable knob and a washer which is used as a spring seat in the plug against the relief spring. This makes a playform for the adjuster bolt to adjust the engine oil pressure. Winding the knob in incr...
Paper gasket for either side of the spacer on all mechanical fuel pumps fitted on the rear of engines. The spacer with gaskets fitted is available as GUG705603GM.
Keyed or cupped, either variety does the job. A plus engines use a TAM2020.
Tappet chest cover seals for all small bore and Cooper S engines (except pre 1966 which use 12A1139). Quantity required-2 per engine.
Turbo oil pump, highest flow available. 9 Gallons per minute as against approx 6 GPM. This pump is a late model slot drive and will fit into any 1275cc engine and exactly the same as the second generation of pump as sold by Unipart/Rover.
Ga...
Gasket for all spin on filter heads to block except aftermarket billet types which use 88G402. For the latest state of the art gasket material see GUG705553GM
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.