PISTON RINGS FOR EVOLUTION +40 PISTON

Race quality Single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.

Sold per piston so 4 packs required per engine.

£16.00 exc vat

£19.20 inc vat

PISTON SINGLE 1275 LOW DRAG +60 8.8CR

P21251-60

60 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.

Typically installation will result in a minimum 8.8:1 compression ratio but on some Metro versions it was higher.

Current pistons ...

£48.00 exc vat

£57.60 inc vat

PISTON RING SET FOR 21250/1 +20

R35960-20

Rover piston TAM2048 stamped 21962 with ring sizes 1.501mm and oil ring 4mm but some pistons have been stamped 21963.

-Does this get confusing?

So lets clear it up; the easy way to identify the piston and corrrect rings are as follo...

£58.44 exc vat

£70.13 inc vat

PISTON RING SET FOR 73.5 C-STR311 + OMEGAS

C-STN96

NPR Ring set for 73.5mm Mega and Omega pistons with 1.2mm thick rings and 3 piece oil rings-also for new range of EVO pistons C-STN101

£78.00 exc vat

£93.60 inc vat

PISTON SINGLE 1275CC LOW DRAG 8.8CR

P21251-00

STD size low drag slipper type pistons with a minimum 8.8:1 compression ratio but on some Metro versions it was higher.

Current pistons differ from the 60s originals, improved with a "low drag" slipper skirt design and a shorter lighter wri...

£48.00 exc vat

£57.60 inc vat

PISTON SINGLE 1275 LOW DRAG +40 8.8CR

P21251-40

40 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.

Typically installation will result in a minimum 8.8:1 compression ratio but on some pre 1984 Metro versions it was higher.

Current...

£48.00 exc vat

£57.60 inc vat

PISTON. SINGLE 998 FLAT TOP LATE TYPE 10.3 TO 1 /

P22463-20

These are suitable for press fit gudgeon pin late type 998 con rods.

sold individually with rings and pin complete

Ringsets are available as R43240-20

£37.50 exc vat

£45.00 inc vat

MINI 1275 CAM LINER SET

MS3063

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

£15.75 exc vat

£18.90 inc vat

MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...

AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.

Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

£26.00 exc vat

£31.20 inc vat

MAINS SET +10 PRE A PLUS/EARLY A+ 1275 ACL

C-AEM91120-10

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

£74.51 exc vat

£89.41 inc vat

MAINS SET STANDARD PRE A PLUS/EARLY A+ 1275 ACL RA...

C-AEM91120-00

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

£71.78 exc vat

£86.14 inc vat

BIG ENDS +10 1300 EXCEPT COOPER S ACL RACE

C-AEB91306-10

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

£71.69 exc vat

£86.03 inc vat

BIG ENDS 1300 STD SIZE EXCEPT COOPER S ACL RACE

C-AEB91306-00

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

£69.06 exc vat

£82.87 inc vat

RIGID ENGINE TO GEARBOX HALF MOON SEAL U

CAM6548

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

£4.00 exc vat

£4.80 inc vat

CRANK THRUST WASHER SET STANDARD 1275

ACL2136

SET OF STANDARD SIZE 1275 CRANK THRUST WASHERS

£11.25 exc vat

£13.50 inc vat

CAM LINER SET 1275

ACL3063

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

£15.75 exc vat

£18.90 inc vat

WATER PUMP FITTING KIT FOR GWP187 AND GWP188

GWP187FK

Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.

£4.00 exc vat

£4.80 inc vat

1275cc PUSH ROD - PERFORMANCE

C-AEG582

Price per rod-1275cc larger 6.35mm diameter push rod. Sold per single rod and 8 required per engine.

The larger diameter improves push rod rigidity as much as possible

without having to modify the block/head push rod ports. Thi...

£8.62 exc vat

£10.34 inc vat

ORIGINAL TYPE CAM FOLLOWER FOR FAST ROAD USE

2A13EVO

Mini Spares cam follower with original convex bottom Radii as used by BMC/Rover and made by Clanceys but less the oil hole. Using Clancey drawings and to our design for better cam performance and lift we have made the push rod recess deeper for stabi...

£2.88 exc vat

£3.46 inc vat

CRANK THRUST WASHER SET 1275 30 THOU OVERSIZE

VPW41-030

Set of +.030 thrust washers for 1275.Very useful for machining down when fitting non S cranks in 1275cc block

£14.00 exc vat

£16.80 inc vat

CRANK THRUST WASHER SET 1275

VPW41

Set of std VP thrust washers for 1275.

£14.25 exc vat

£17.10 inc vat