CAM FOLLOWER HI-GRADE TAPPET SET OF 8

The ultimate cam follower with oil hole, designed to minimise float and jump normally seen in original cam followers, which ultimately loses power. Precision ground outside diameter with smaller chamfered base to give more surface area for extra hi l...

£29.06 exc vat

£34.87 inc vat

MINI 1275 CAM LINER SET

MS3063

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

£15.75 exc vat

£18.90 inc vat

CAM LINER SET 1275

ACL3063

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

£15.75 exc vat

£18.90 inc vat

PUSH ROD 1275 AFTERMARKET

AEG314MS

NON GENUINE for standard use only. These are the only type available at the moment and not as accurate as the original Rover product. The genuine factory pushrod was a very good product and does not need routine replacement. The strength and size of ...

£2.70 exc vat

£3.24 inc vat

CAMSHAFT LINER SET 850 998 & 1100

AEC3046

Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...

£12.09 exc vat

£14.51 inc vat

BELT KIT OIL SEAL SMALL

BELTSEAL1

Lower rubber seal for belt-drive timing gear.

£1.50 exc vat

£1.80 inc vat

CAMSHAFT RETAINING NUT

6K629

Special flat nut (1-5/16" AF) for camshafts, uses 2A759 locktab.

£6.16 exc vat

£7.39 inc vat

CRANK THRUST WASHER SET STANDARD 998

ACL2122

Set of standard size 998 thrust washers.

£9.75 exc vat

£11.70 inc vat

AC DODD ROAD SPORT CAM

ACD-RS

AC Dodd Road Sport camshaft, ideal for those wanting the most from a tourer cam whilst still have a smooth idle. Please see picture for full cam specs.

Road Sport, For those requiring the maximum from a tourer cam, excellent road m...

£214.40 exc vat

£257.28 inc vat

TIMING COVER AND FRONT PLATE FITTING KIT

MSSK063

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

£8.00 exc vat

£9.60 inc vat

SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275 +40

C-STN103-40

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

£299.00 exc vat

£358.80 inc vat

SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275 +20

C-STN103-20

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.

Glyn Swif...

£299.00 exc vat

£358.80 inc vat

SWIFTUNE PERFORMANCE DIE CAST PISTON SET 1275 +60

C-STN103-60

These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...

£299.00 exc vat

£358.80 inc vat

PISTON RINGS FOR EVOLUTION +40 PISTON

C-STN102-40

Race quality Single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.

Sold per piston so 4 packs required per engine.

£16.00 exc vat

£19.20 inc vat

CRANK THRUST WASHER SET +0.30" 1275

ACL2136-030

Set of +0.030" size 1275 crank thrust washers.

£11.25 exc vat

£13.50 inc vat

CRANK THRUST WASHER SET +0.003" 1275

ACL2136-003

Set of +0.003" size 1275 crank thrust washers.

£11.25 exc vat

£13.50 inc vat

MINI SPARES COMBINED BLOCK/GEARBOX GASKET AND SEAL...

AJM100MS

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.

Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

£26.00 exc vat

£31.20 inc vat

MAINS +10 1275CC A PLUS ONLY ACL RACE

C-AEM91886-10

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

£78.62 exc vat

£94.34 inc vat

MAINS STANDARD SIZE 1275CC A PLUS ONLY ACL RACE

C-AEM91886-00

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

£78.62 exc vat

£94.34 inc vat

MAINS SET +10 PRE A PLUS/EARLY A+ 1275 ACL

C-AEM91120-10

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

£74.51 exc vat

£89.41 inc vat

MAINS SET STANDARD PRE A PLUS/EARLY A+ 1275 ACL RA...

C-AEM91120-00

ACL Race Bearings

ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.

What is the purpose of ACL Race series bearings?
...

£71.78 exc vat

£86.14 inc vat