£6.16 exc vat
£7.39 inc vat
In stock
£6.16 exc vat
£7.39 inc vat
In stockRecommended usage 1 x 6K629 to fit one mini.
Good maintenance, just as you would never rebuild your motor without replacing the crank thrust washers, you should also care about the camshaft thrust plate. Sometimes called the "triangle plate" this small but important plate doesn't just hold the ...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all 1275cc blocks plus 970 and 1071 Cooper S. It's almost too simple and thus often overlooked during a rebuild. Camshaft bearings are pressed...
Price per rod-1275cc larger 6.35mm diameter push rod. Sold per single rod and 8 required per engine.
The larger diameter improves push rod rigidity as much as possible
without having to modify the block/head push rod ports. Thi...
NON GENUINE for standard use only. These are the only type available at the moment and not as accurate as the original Rover product. The genuine factory pushrod was a very good product and does not need routine replacement. The strength and size of ...
"Scatter Pattern" cams were designed by David Vizard to work best with the pecularities of the A-Series' siamese intake ports. The 310 scatter pattern is the ultimate race cam. Needs fully prepared engine for good results - high CR, high flow head, ...
Original equipment quality for factory built engines giving longer life expectancy on road cars under variable conditions of oil and use. These are the 1275cc mains as fitted to A Plus engines with the locating tab in the middle rather than to the ou...
Genuine Mini Spares engine front plate for pre A+ plus timing gear.
this fits engines using the early egg shaped cover
This plate has been modified by counter sinking the 2 main cap bolt holes to accept countersu...
AC Dodd Road Sport camshaft, ideal for those wanting the most from a tourer cam whilst still have a smooth idle. Please see picture for full cam specs.
Road Sport, For those requiring the maximum from a tourer cam, excellent road m...
AC Dodd Road Torque cam, great for low end power. Please see picture for full cam specs.
Road torque, this cam for strong low & mid range lugging, Touring, Smooth idle, excellent emmisions
ACD - RT
Power...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Steel ring set, 3 compression ring @ 0.625" oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102
This is the large seal for the early type oil filter assembly pre spin on type.
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.
Glyn Swif...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.