£1,363.61 exc vat
£1,636.33 inc vat
In stock
This unit, the 1030cc model, is fitted with our ultimate road camshaft, the EVOLUTION001.
The engines are all 9-Stud and come with, oil pump, core plugs, gallery plugs, front plate, duplex timing gear assembly. These units do not come fitted with a timing cover.
£1,363.61 exc vat
£1,636.33 inc vat
In stockRecommended usage 1 x ENG101 to fit one mini.
24.5-25.5cc combustion chamber for use with flat top pistons. This specification of cylinder head is the only modified version for the small-bore based engines Mini Spares supply as it is judged to be the only one worth up-grading to. Based on used c...
The distributor drive spindle in all A plus engines which is now obsolete from the factory and Xparts but remanufactured as NON genuine.
Brass type core plug for engine. Originally, engines had brass oilway plugs (2K1345) 1/4" hole fitted. These cup type plugs replaced them about 1985. 12.7mm cup type plug about 9.6mm deep. Fits 1/2" hole.
All good engine tuners ...
3 Bolt hole fixing pump for A plus 998cc engines. This has a spade type drive spindle to fit the slot in the camshafts. This replaced earlier peg type drive which fitted into camshafts with a pin (known as pin drive).
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road car.
( Tri-Metal )
Sintered copper lead, lead...
Cup type core plug for all A plus and 1275cc engines except for Cooper S. 33.6mm wide.A plus 5 required but only 4 on 998 A plus. 1275 has 2 core plugs oil pump end of block whereas 998 only has one
Steel center main strap for small bore engines, comes with longer high tensile bolts. The Main bearing top cap will need machining flat, no other modifications required. Engine bolt hole centres all slightly vary from 2.775" to 2.785" - some 0.010" o...
Good maintenance, just as you would never rebuild your motor without replacing the crank thrust washers, you should also care about the camshaft thrust plate. Sometimes called the "triangle plate" this small but important plate doesn't just hold the ...
Standard cast duplex gear set from the original AE supplier. for road use only.
Found to be the best fitting in Mini Mag feature Autumn 2007.
Driving the cam and controlling the timing relationships between the cam and the crank i...
Plastic tensioner pad to take up the slack in single row timing chains on A plus engines that wears and should be replaced nearly every time you have the timing cover off. From engine numbers 99H791/10H791 AND ALL A+. Fitted to 998/1100cc from 1979 a...
A plus bearings have a centre locating indent whereas the earlier blocks had the locating area on the side. These are A plus standard size. Fitted from 1984/5 on.
VP suffix bearings are made by Mahle with lead indium content for road or rac...
Standard size crankshaft washers as a set of four, fits 998 and 1100cc.
Set of 8, original leyland ST product but now made for us to our specification. Critical to the life and performance of the camshaft is the use of high quality cam followers. Remember, they operate in a finite hole and thus the dimensional tolerances...
Available at the moment but they sporadically become unavailable. Mini Spares have also had a batch of plus 60s specially commissioned to us for Grass trackers and racers. sold individually with rings and pin complete.
Ringsets are availabl...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Genuine Mini Spares camshaft,great for all road uses- A Plus slot drive only.
Valve clearance should be 0.014" on inlet and 0.016" exhaust. LCA 107 degree
DURATION INLET 264 EXHAUST 268, LIFT INLET 264 EXHAUST 289.
This ca...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.