CENTRE MAIN STRAP & BOLTS - 998cc BLOCKS
CMS10

£8.94 exc vat

£10.73 inc vat

In stockIn stock
Steel center main strap for small bore engines, comes with longer high tensile bolts. The Main bearing top cap will need machining flat, no other modifications required. Engine bolt hole centres all slightly vary from 2.775" to 2.785" - some 0.010" o...

£8.94 exc vat

£10.73 inc vat

In stockIn stock

Recommended usage 1 x CMS10 to fit one mini.

Kit products
1030cc (998+40) A+ HALF ENGINE
ENG101

We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...

£1,363.61 exc vat

£1,636.33 inc vat
Kit contained products
BOLT FOR CMS10 3.25"LONG 7/16"
CMS10BOLT

The high tensile bolts supplied with the 998 centre main strap kit.

£1.77 exc vat

£2.12 inc vat
People also bought products
TIMING COVER AND FRONT PLATE FITTING KIT
MSSK063

Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).

£8.00 exc vat

£9.60 inc vat
ENGINE TO GEARBOX NUT AND BOLT KIT
MSSK060

Complete nut, bolt and washer set for engine to gearbox only

£3.50 exc vat

£4.20 inc vat
WATER PUMP FITTING KIT FOR GWP187 AND GWP188
GWP187FK

Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.

£4.00 exc vat

£4.80 inc vat
WATER PUMP FITTING KIT FOR GWP134 AND GWP132
GWP134FK

Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.

£8.00 exc vat

£9.60 inc vat
BOLT OIL FILTER HEAD TO BLOCK
LYG10008

later cars used this bolt to hold on the spin on filter head to the block-earlier cars used the CHS2613 stud--both are interchangeable

3/8"unc 1"long

£2.10 exc vat

£2.52 inc vat
CRANK BOLT LONG CAPHEAD WITH AND SPECIAL WASHER
C-AHT147

A series mini engine crank pulley bolts have been known to come loose, caused by pulley damper vibration on competition engines. This is a high tensile longer extended thread cap head bolt with thick washer to rectify this problem and also allow furt...

£8.91 exc vat

£10.69 inc vat
BOLT FOR CMS13 3.5" LONG 7/16"
CMS13BOLT

Longer main bolt stud.

As supplied with our main strap kit.

£2.70 exc vat

£3.24 inc vat
BOLT FOR CMS10 3.25"LONG 7/16"
CMS10BOLT

The high tensile bolts supplied with the 998 centre main strap kit.

£1.77 exc vat

£2.12 inc vat
OIL PUMP BOLT 1/4"x1.625"(1 5/8")LONG UNF
BH604131

Fits all current range of oil pumps including GLP110MS.

Holds C-AHT54 oil pick up or standard oil pipe to case on outside of gearbox case 1/4"unf bolt 1.625"long

3 lengths of oil pump bolts have been used s...

£0.90 exc vat

£1.08 inc vat
CUP WASHER FOR TAPPET CHEST GROMMET
12A1177

The special washer under the tappet cover bolt.Sold singly 2 required per engine.

See 12A1176 for seal

£0.80 exc vat

£0.96 inc vat
OIL PUMP BOLT CONCENTRIC/TURBO. SEE NOTES.
BH604141

1.75" LONG shouldered 1/4" bolt fits original concentric pumps plus some GLP139 and GLP110MS - check that you need a bolt this length as many later pumps require shorter bolts. This can of course be cut down or see [link]BH6...

£0.83 exc vat

£1.00 inc vat
ROCKER STUD LONG 3" x 5/16" UNC
51K885

Using new hardware makes any job more pleasant. If you're servicing your cylinder head you should examine the rocker studs for signs of stretching or stripped threads. Two long (51K885) and two short (51K1473) per head.

This is ...

£1.25 exc vat

£1.50 inc vat
MAINS STUD "S"(set 2 long 4 short)
AEG323

STUD SET,(6)"S" MAINS

£94.50 exc vat

£113.40 inc vat
STEADY ROD BOLT FOR 21A1109 BAR TO ENGINE - 1 7/8"...
BH605151

Engine stabiliser arm to block bolt. This is the longer bolt that fits the engine stabiliser rod to the cylinder block.

£1.00 exc vat

£1.20 inc vat
CON ROD NUT "S" RACE ALTERNATIVE
EAC5541A

This alternative multi point nut was preferred by racers because the plastic locking part of the original AEG147 could fall out under extreme conditions on an over hot running engine. Current AEG147 are now an all metal nut ...

£2.25 exc vat

£2.70 inc vat
STUD FOR SCREW ON OIL FILTER PLUS HS2 CARB
CHS2613

3/8"unc 1.6250" long stud for engine block to accept the TAM2097 screw on filter head and for HS2 carbs, alternative to this is CHS2614 1.75" long and just over one thread longer. LYG10008 bolt was ...

£1.68 exc vat

£2.02 inc vat
CRANK THRUST WASHER SET STANDARD 998
ACL2122

Set of standard size 998 thrust washers.

£9.75 exc vat

£11.70 inc vat
AC DODD ROAD SPORT CAM
ACD-RS

AC Dodd Road Sport camshaft, ideal for those wanting the most from a tourer cam whilst still have a smooth idle. Please see picture for full cam specs.



Road Sport, For those requiring the maximum from a tourer cam, excellent road m...

£214.40 exc vat

£257.28 inc vat
REPLACEMENT SEAL O-RING FOR MSA1134. MSA1124/5 DIP...
TRS1316

Replacement O ring for the Minispares range of chrome dipticks

£0.10 exc vat

£0.12 inc vat
MINI 1275 CAM LINER SET
MS3063

You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...

£15.75 exc vat

£18.90 inc vat