£1.45 exc vat
£1.74 inc vat
In stock
All good engine tuners would remove them for cleaning sludge but these later cup type are much easier to remove and replace. 4 required ON LARGE BORE AND 2 required ON SMALL BORE.
£1.45 exc vat
£1.74 inc vat
In stockRecommended usage 4 x 12G3503 to fit one mini.
Small brass tapered plug fits 1/4" hole for the oil release passage PRE 1985 on Metro blocks which most engine tuners replace to clean out any sludge - 6.95mm tapering down to 6.25mm - also used as a general engine plug but mostly as a cylinder head ...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
We have teamed up with Bill Richards Racing to produce a new range of built up short engines ready to drop in. These engines are as fast and as powerful as you can get, whilst still keeping the on road driveability and a reasonable MPG figure.
<...
Cup type core plug for all cooper S only @ 41.4mm wide.
4 required per engine.
Convex type core plug at 41.4mm for all early A series blocks up to A plus.
4 required per engine-these are known as the flat type wher the centre has to be pressed in so the convex plug spreads out. The Cooper S althouh same size was a cup ...
Cup type core plug for all A plus and 1275cc engines except for Cooper S. 33.6mm wide.A plus 5 required but only 4 on 998 A plus. 1275 has 2 core plugs oil pump end of block whereas 998 only has one
Original equipment quality for factory built engines giving longer life expectancy on road cars under variable conditions of oil and use. These are the 1275cc mains as fitted to A Plus engines with the locating tab in the middle rather than to the ou...
Genuine Mini Spares engine front plate for pre A+ plus timing gear.
this fits engines using the early egg shaped cover
This plate has been modified by counter sinking the 2 main cap bolt holes to accept countersu...
AC Dodd Road Sport camshaft, ideal for those wanting the most from a tourer cam whilst still have a smooth idle. Please see picture for full cam specs.
Road Sport, For those requiring the maximum from a tourer cam, excellent road m...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Minispares steel connecting rods are machined by Arrow Precision Eng from double air re-melted 817M40 forgings to X condition. Weight 445g per rod
The new X rod design maintains stiffness whilst reducing weight where it is not required. ARP ...
Minispares steel connecting rods are machined by Arrow Precision Eng from double air re-melted 817M40 forgings to X condition. weight 452g
The new X rod design maintains stiffness whilst reducing weight where it is not required. ARP 2000 5/1...
Steel ring set, 3 compression ring @ 0.625" oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.
Steel ring set, 3 compression ring @ 0.0625" oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
11/16" dowty seal for post 1991 cars where the original pipe has been replaced with a braided pipe or an oil cooler has been fitted using part number MOC4. used on the TCZ102
This is the large seal for the early type oil filter assembly pre spin on type.
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading German F1 piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience.
Glyn Swif...
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.