£255.60 exc vat
£306.72 inc vat
In stock
As of July 2007 Kent cams have no supply of old camshafts for reprofiling and we will only supply camshafts fro...
£255.60 exc vat
£306.72 inc vat
In stockRecommended usage 1 x MDM274MPI to fit one mini.
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
A vital aid for accurate valve timing this disc is a 360 degree protractor disc made by kent cams.
Genuine camshft,Unique to MPI-has a very distinguishable twin prong lobe for the Twin point injection pick up and is therefore unique to this model only. Distributor drive usually machined off.
alternative mild tune camshaft is available [li...
Genuine Mini Spares camshaft,great for all road uses- A Plus slot drive only.
Valve clearance should be 0.014" on inlet and 0.016" exhaust. LCA 107 degree
DURATION INLET 264 EXHAUST 268, LIFT INLET 264 EXHAUST 289.
This ca...
woodruff key to fit in the camshaft to hold the larger timing chain gear. See 6K836 for the crankshaft keyway for the lower smaller timing chain gear
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Converted into a non melting type grease.Favoured by proffessionals for camshaft,lobes and lifter,and any valvetrain to stop scuffing on start up. Also useful for oil pumps to stop drain back on start up
Lightened cam gear duplex timing gear and chain set. Not recommended for race/rally applications. approx 69-70g 9% lighter
General: Camshaft Drive Systems
For highly tuned engines always use steel duplex as cast is nowhere as st...
Standard weight, 44.00grams, follower with oil drain hole. Always check for wear and replace whenever a new camshaft is fitted. These are manufactured by the supplier to AE Hepolite the original engine components manufacturer and should be coated wit...
MD266 in A plus form with cam followers.valve springs and initial set up oil.
For timing disc, order separately as C-AJP337
As of July 2007 Kent cams have no supply of old camshafts for reprofiling a...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
Standard cast duplex gear set from the original AE supplier. for road use only.
Found to be the best fitting in Mini Mag feature Autumn 2007.
Driving the cam and controlling the timing relationships between the cam and the crank i...
Timing belt camshaft drive systems have been around for a number of years, in fact for a lot longer than the life expectancy of the belts. If you have a belt drive conversion you should have one of these replacement belts. If you want to keep things ...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...
These Swiftune die cast performance pistons are part of their new Heritage range and are manufactured by global leading F1 German piston manufacturer Mahle. These pistons have been developed using their 50 plus years of experience. Glyn Swift was usi...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
ACL Race Bearings
ACL Race series bearings are precision manufactured to a wall thickness of ±0.0040mm giving engine builders close control of vertical oil clearance.
What is the purpose of ACL Race series bearings?
...
Race quality heavy duty double row performance endless timing chain. It is the best chain available and used by top engine builders, also fits MGB/Midget. This chain is for duplex gears that is used by racers as a limited stretch heavy duty version m...
Special superb extra strong timing chain with very limited stretch using modern day materials and technology to keep your timing correct and will fit any A series engine using a single row chain.
This chain saves all the time and effort requ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.