£44.80 exc vat
£53.76 inc vat
In stock
£44.80 exc vat
£53.76 inc vat
In stockRecommended usage 1 x C1072-60 to fit one mini.
1.59MM (0.625")COMPRESSION RINGS 3.175mm (1/8")single oil control ring.
also available is a high grade ring set C-STN99-60with 3 piece oil ring
Steel ring set, 3 compression ring @ 0.625" oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Complete fixing kit for a water pump, includes replacement silicone bypass hose, clips, superseal gasket, replacement bolts and washers.
Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead...
Con Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead...
NON GENUINE for standard use only. These are the only type available at the moment and not as accurate as the original Rover product. The genuine factory pushrod was a very good product and does not need routine replacement. The strength and size of ...
Mini Spares cam follower with original convex bottom Radii as used by BMC/Rover and made by Clanceys but less the oil hole. Using Clancey drawings and to our design for better cam performance and lift we have made the push rod recess deeper for stabi...
The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...
Genuine Mini Spares camshaft,great for all road uses- A Plus slot drive only.
Valve clearance should be 0.014" on inlet and 0.016" exhaust. LCA 107 degree
DURATION INLET 264 EXHAUST 268, LIFT INLET 264 EXHAUST 289.
This ca...
Favoured by proffessionals for press fitting pistons, pre lubing bushes, roller and plain bearings, journals and gears. Prevents scuffing, seizure, wear, rust. Waterproof and corrosion proof.
Standard size crankshaft washers as a set of four, fits 998 and 1100cc.
For race quality chain see 2H4905EVO.
It only makes sense that if you have your engine out of the car that you replace the timing chain. The chain controls the timing of the camshaft and even a slight amount of wear or stretch c...
If you are replacing your timing chain or just doing routine maintenance a new locktab is sure to come in handy.
ACL Main bearings for the crankshaft as preferred by performance engine builders standard size
Sintered copper lead, lead plated,steel backed
Nominal Composition
Copper 74%
Lead 24%
Tin 2%
Adjustable cam gear set with non stretch chain. Cam gear weighs 674g
Even a stock camshaft needs to be timed correctly. If you want to get the maximum benefit from a "hot" cam it is doubly important that the cam timing be correct. This adju...
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road car.
( Tri-Metal )
Sintered copper lead, lead...
3 Bolt hole fixing pump for A plus 998cc engines. This has a spade type drive spindle to fit the slot in the camshafts. This replaced earlier peg type drive which fitted into camshafts with a pin (known as pin drive).
Rod bearings, 850-1275 1 5/8" journals. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use on a fast road motor.
( Tri-Metal )
Sintered copper lead, le...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.