Fitted from 1976 on the right hand side of steering wheel, until 1984 when they fitted them on the same side as overseas cars on the left see 21A2660.
Originaly designed to suit the charcoal grey wooden dash boards the complete set is as follows
MSA0200 door cappings
MSA0201 door pull handles
MSA0202 window winder handles
MSA0203 handbrake lever
MSA0205 ...
Fitted on the left hand side on 1976-1989 LHD cars and on UK cars from 1984-89.
This easy to install metal extension clamps right on to the existing pedal. While it wont make the car any faster, it will make driving more leasurable. Will only fit pre 1976 cars with small pedal.
This universal trim clip with smaller D shape and exta short claws section is for rear seat and for headlings. For MK1/2 minis and Traveller/Estate versions there are 25 and MK3 on there are 13.
For the clip with a larger D and claw spike se...
Complete assembly includes 2 shear bolts, lock, ignition switch & barrel assembly and even a spare key. Wiring loom has a four-pin plug. Fitted from MK4 mini (1976 to 1996) up to the introduction of MPI which had air bags fitted and different steerin...
This turn signal indicator switch also includes a black button on end for the horn push and a for and aft movement for the activation of high beams. The switch is used on most MK3 Minis and can be distinguished by the use of a plug for interconnectio...
Under all seat covering is a foam and this is the rear seat foam squab,the part you sit your back against for saloons from 1967-1980.The foam fits over the rear seat frame and is folded over that frame to give soft corners. The vertical
bol...
R/H/D Alloy dashboard for cars wuth 3 clock pod in front of driver and knob on glove box. This dash has 3 extra gauge holes.
do not fit mpi
MK3 minis introduced a different headlining which was held up by rods rather than the MK1/2 type which were attached to a frame. There are five different colour codes on the 6 rods:
number 1 with red ends is EEB100060
n...
See also PAM5401LNG and PAM5401AP
These headlinings are held in by different shape/length rods which are NOT included but we do include the rear corner cloth side sections between the rear side window and backlight ...
with headrest-this fixed back traditional bucket seat is the entry level
version of Cobra seats and has deep sides and a low back to ensure comfort and support without the restrictions of a larger seat. black nylon and no piping- a vinyl ver...
Front seat base foam.This cushion can be used for most models during this period but mainly for 1967-80 with a more defined shape with its raised sides in contrast to the flat foams on earlier production. It is approx. 2" thick with raised sides to g...
Known as a seat base foam wrap it is just a simple item, but when fitted to the base frame of your seat frame under the seat main trim cover skirt,it will soften the look of the frame and protect the cover from damage.
Late type swith carrier with 4 square holes plus heater and choke cable holes-uses the ratchet type choke cable with D shape fitting--earlier cars used round hole for pull and push chooke cableCZH3591
Very front left hand air nozzle behind the grille on injection cars - earlier cars used CZH1318
These headlinings are held in by different shape/length rods which are NOT included but we do include the rear corner cloth side sections between the rear side window and backlight which are not in other suppliers kits. Fitted 1977-92
Also...
Dash liners with air vents for on de luxe versions with centre speedo and two gauges which are black vinyl covered as opposed to the painted type. Not for the single centre clock only. The cardboard is cut out but the vinyl needs trimming when fittin...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.