VALVE EXHAUST TRIPLE GROOVE 29.5MM RACE QUALITY
C-AEG105

($19.55) £19.55 exc vat

($23.46) £23.46 inc vat

In stockIn stock
1.158" (29.4) dia exhaust valve for 12G940 casting.

Our race valves are produced in EN214N stainless steel and require Manganese/Silicon bronze alloy valve guides. They are stellite tipped and have the triple collet groove and current valve head shapes. These valves are heat treated to eradicate wear from unleaded petrol.



As it is possible, even common, to swap one head for another on 1275 engines, be aware that if the head has been worked on previously, it may have oversize valves, it may have undersize if seats have been installed. Unless you are 100% sure what is in your cylinder head, it is a good idea to remove a valve for accurate measurement. There are two lengths used (nominally 3.52" & 3.57") three different keepers, (wide, narrow, and three-groove) and many different head diameters.



Note that 12G1316 (Smog-Type), all variations of the 12G940, and the latest CAM head castings all use the following 3.57" long valves.

($19.55) £19.55 exc vat

($23.46) £23.46 inc vat

In stockIn stock

Recommended usage 4 x C-AEG105 to fit one mini.

Recommended products

As an engine wears, the clearance between the valve stem and guide increases; as this gets beyond tolerances the car will tend to smoke under deceleration (when you take your foot off the throttle). Good valve stem seals will allow for greater wear b...

New colour, PB104 bronze guides.Although Silicon bronze valve guides were used for their extremely good wear values, they were very hard and not user friendly when fitting. These valve guides are recommended when using all EN21 4N stainless steel val...

when removing the head for a decoke or changing valves/springs you will require this tool to release the collets holding the valves in place.

Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.

Man...

Kit products

35.7 x 29.5mm race valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides. Nominal 21.4cc with by pass and heater take off holes open.

This specification of cylinder head, based on used core castings, is modified to curr...

35.7 x 29.5mm race valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides, Nominal 21.4cc with by pass hose and heater take off holes open. This specification of cylinder head, based on used core castings, is modified to current...

35.7 x 29.5mm valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides.Nominal 24-25cc with by pass and heater take off holes open. Supersport head-sold on an exchange basis-old core must be serviceable and no cracks--See [link]...

35.7 x 29.5mm race quality valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides. Nominal 21.4cc with No by pass or heater take off holes open. This specification of cylinder head, based on MPI castings, is modified to current ...

Hi spec all new alloy 5 port gas flowed head. Outright sale to save you the risk of losing £240 on exchange schemes where old heads are traded in and where faults are found, especially by some companies.

Speak to York branch for all modifica...

35.7 x 29.5mm valves in plasma-nitrided EN214N s/steel with manganese bronze valve guides. Nominal 21.4cc with by pass and heater take off holes open. This specification of cylinder head, based on brand new twin point injection castings (modified to...

People also bought products

New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the v...

New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the valves and easier to control spring heights.

30.5mm(1.2") longer exhaust valve for the 2012 on 8 port head only

for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol--For earlier heads see C-AHT376/7 valves.

The valve size h...

Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.

35.6mm(1.4") longer exhaust valve for the 2012 on 8 port head only

for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol--For earlier heads see C-AHT376/7 valves.

Valves now longe...

37mm(1.457") longer inlet valve for the 2012 on 8 port head only

for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol



3.933" 99.898mm long

Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.

Man...

Best quality 1" exhaust valve for small bore cylinder heads as fitted standard to 998 Cooper. Higher grade than AEA434. Has a large 8.65mm (.340") collet groove 2A11 cotters which are now available as 2A11EVO.

1.1" diameter intake valve for 948cc with 8.65mm wide groove for use with the original 88G616 top caps and 2A11 cotters which are now available as 2A11EVO.

Sold individually.

To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.

160lbs on the nose at 400" for standard Cooper S or twin spring set ups. See C-AEA526 and C-AEA527 for later developed springs. These are ok for all standard uses but are improved and uprated over all original factory fitted...

Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...

Early Large cotter groove exhaust valve. Most small bore engines seem particularly prone to burning valves, it is highly recommended to replace the exhaust valves when you do a valve job! This 1.0" valve fits most early 948cc, 998cc and 1098cc engine...

We stock a limited range of Paul Ivey developed Rimflow valves for the A-Series.

30.9mm (1.217") diameter exhauste valve for 12G940 large bore casting is oversized to the stock version. Not only can you pick-up performance from...

1.402" (35.6mm) dia x 3.57" long intake valve.

Our race valves are produced in EN214N steel and are stellite tipped and use the latest triple collet groove and current valve head shapes, plasma heat treated for eradicating unleaded petrol we...

1.311" (33.3mm) dia x 3.57 long intake valve.


Our race valves are produced in EN214N steel and rquire Manganese/Silicon bronze alloy valve guides. use the later narrow, single collet groove and current valve head shapes.


As ...

1.220" (31mm) dia x 3.57 exhaust valve.

Our race valves are produced in EN214N steel and are stellite tipped and use the later narrow, single collet groove and current valve head shapes.These valves are plasma heat treated to eradicate wear ...

1.401" dia x 3.52" long intake valves. Our race valves are produced in EN214N steel, stellite tipped and use the later narrow collet groove and current valve head shapes. As it is possible, even common, to swap one head for another on 1275 engines, i...

Genuine Mini Spares product as everything else on the market was poor fitting and unstable.

For Performance see 88G459EVO made in the USA by a Specialised Racing product company.

All the earlier heads used the 2A11 cott...