($2.50) £2.50 exc vat
($3.00) £3.00 inc vat
In stock
($2.50) £2.50 exc vat
($3.00) £3.00 inc vat
In stockRecommended usage 1 x GDC136CLIP to fit one mini.
Electronic ignition conversion. For points type distributors, fixed or sliding. Negative earth only. Also, available for earlier 23/25D on Negative earth (LU142) or earlier 23/25D with Positive earth (LU142AP12).
ONLY use GCL217 coil for bal...
Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.
Brand New distributor complete with electronic conversion already fitt...
RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...
Electronic Distributor for any standard A+ 998cc. Negative earth only.
From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...
NEGATIVE EARTH ONLY..45D electronic(contactless)Pre A plus distributor .
replaces 41824A and 41418 plus any 998/1098cc up to the changeover of A plus type distributors. For best performance and tune we advise our electronic evolution versio...
NEGATIVE EARTH ONLY. Cooper"S" 23D distributor, no vac unit-This is NOT THE ORIGINAL LUCAS ITEM but a new contact less electric copy of 40819 to cope better with modern day fuels. Fitted with the better Red rotor arm upgrade.Cheaper than many electro...
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
fitted to ducellier distributors only which are recognised by their red cap.
The O ring that actually sits on the distributor drive spindle shaft in the recess provided.
The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...
Electronic ignition kit to fit 45/59D4 distributors.
Designed to do away with points this is a simple drop in installation to fit into your existing distributor. Also see our range of distributors with built in electronics--BAU1962MS & [lin...
Aldon modified yellow equivalent on the original 45d body early pre A plus Once the engine has been modified, it will invariably require a different ignition curve-especially when compression ratios have been raised and camshafts changed. There is no...
This "Pigtail" wire is all that carries current through the distributor to the points.Fits 23 and 25d type distributors
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.