DISTRIBUTOR CLAMP FOR A PLUS DIZZY 85 ON
TAM1671

£6.00 exc vat

£7.20 inc vat

In stockIn stock
Prong type clamp that bolts to the block and retains the A plus distributor in place. The screw is TAM1706.

Pre A plus clamp is 501134

£6.00 exc vat

£7.20 inc vat

In stockIn stock

Recommended usage 1 x TAM1671 to fit one mini.
998cc, 1981 on, 'A' Plus Block - Qty 1
A Plus Blocks 1275 Engines with 12H Engine No - Qty 1
Distributors - Qty 1
Distributors - Qty 1

Recommended products

the bolt that holds distributor clamp TAM1671 in the block on A Plus engines

now obsolete use 3/8"unf bolt with thread length of 1"

People also bought products

Pre A plus Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles

Brand New distributor complete with electronic conversion already fitted.

PRE A PLUS
<...

Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.

Brand New distributor complete with electronic conversion already fitt...

Fits our 45/59d distributors, 1275cc as fitted to 12G4180 and ADU3825

Along with our distributor manufacturer we have found this to be the best for modern day fuels for all 45 or 59d distributor for 1275cc uses as...

Electronic Distributor for any standard A+ 998cc. Negative earth only.



From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...

NEGATIVE EARTH ONLY..45D electronic(contactless)Pre A plus distributor .

replaces 41824A and 41418 plus any 998/1098cc up to the changeover of A plus type distributors. For best performance and tune we advise our electronic evolution versio...

NEGATIVE EARTH ONLY. Cooper"S" 23D distributor, no vac unit-This is NOT THE ORIGINAL LUCAS ITEM but a new contact less electric copy of 40819 to cope better with modern day fuels. Fitted with the better Red rotor arm upgrade.Cheaper than many electro...

This is a race or high performance disributor for A Plus engines and can be fitted with points or LU143A ignition pack can be fitted as an extra

Distributor drive spindle if required is 12G3560

Distributor clamp plate...

These performance road type distributors are for A Plus engines and can be fitted with points or LU143A ignition pack can be fitted as an extra

For best performance and modern day fuel/camshafts and tune we advise our electronic evolution v...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For an...

If you want to tune your engine, or you have an engine for which there is no standard distributor available.....the new 123\TUNE is the answer ! By connecting it to a computer, the end-user can easily adapt the 123\TUNE to fulfill even the most deman...

CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference!|nNeg earth only.

After removing the cap you can select between 16 different curves by using

a screwdriv...

CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference!Neg earth only

After removing the cap you can select between 16 different curves by using

a screwdriver....

These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106

Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.

Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.

Replacement service items for this are:

Cap GDC156

Rotor arm GRA2143

Should be used with GC...

Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.

If you have a new 123 ELECTRONIC distributor this is the replacement cap.

For earlier 123 distributors please see part number GDC123E.

Rotor arm is GRA123

If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 pre programmed advanced curves built in, a must for any mini with a worn distributor. Full instructions are included with the system. For any A series, A Plus engines...

The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For any...