£217.50 exc vat
£261.00 inc vat
Out of stock
After removing the cap you can select between 16 different curves by using
a screwdriv...
£217.50 exc vat
£261.00 inc vat
Out of stock
Modified by Aldon to their Yellow distributor spec on 45/59D type body with vacuum advance for Aplus performance road engines.
Once the engine has been modified, it will invariably require a different ignition curve-especially when comp...
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
Original mini coil fitted to all cars up to 1983.
3ohms
NOT for ballast type ignition systems.
Our research, sales and feed back shows Intermotor coils to be the best available for the mini.
Original type coil bra...
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
This was the first mini distributor cap to have screws hold the cap to the body from about 1990 on, when electonic ignition was introduced. Therefore there is no points or condenser but the rotor arm to use is GRA2143. Fits all 1992 onwa...
This is the standard non ballast coil as used on the late Mini with factory electronic ignition for use with 65D distributor.0.9ohms.
GCL143 was the Genuine Rover part fitted part on 1275cc from 1990.
0.9ohms
GCL2...
Slightly hotter running engine plug for A Plus 998 and all 1275cc standard engines. For engine running CR of 9.4 to 10:1
100% silicon insulation, silicon coated suppressed conductor,braided glass reinforcement,increased working temperature 0f minus 50C to +300 degrees with improved resistance to damp and water, great fitting and spiral bound wire giving instant and gre...
Also see 8B12398 which also includes coil cover sleeve in stainless steel.
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
100% silcone translucent outer sheath, 8mm lead set with stainless steel wire spiral bound wire giving instant and greater resonance, Kevlar fibre core and a ferromagnetic layer for EMC suppression by Luminition. Top end of ignition lead sets.
This sleeve fits most Lucas and Unipart coils to give the impression thay are stainless steel. Comes with a s/steel bracket. Covers just over 4.25"(11cm)long
Blue in colour these points were used on the latest 59D type distributors from about 1980 on up to the introduction of electronic distributor with only rotor arm."Sliding" points for 59D4 distributors, keep a spare set!
Ultimate coil from lumenition has spiral bound wire giving instant and greater
resonance. Not Suitable for injection Mini's.
For sports coil for use on resistor type cars 1982 to 1992 with 998cc engine from factory, MSC110<...
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm silicon wire and the highest performanc...
Introduced in 1974 on the 45d type distributor with the larger GDC136 cap this Unipart Rover condenser was used right up to the introduction of electric distributors.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.