£156.36 exc vat
£187.63 inc vat
In stock
Once the engine has been modified, it will invariably require a different ignition curve-especially when compression ratios have been raised and camshafts changed. There is no substitute for a tailor-made distributor determined by an engine or chassis dyno session, however this can be prohibitively expensive! We offer the Aldon Automotive range of distributors for A Series engines.
For road use it is advisable to use the vacuum advance for economy. Many say, incorrectly, that this over-advances ignition, causing detonation in performance engines. That is not true as the vacuum advance only works at partial throttle openings, not under load with full throttle when no manifold vacuum exists!
Distributor drive spindle if required is 12G3560
Distributor clamp plate is TAM1671
Bolt for clamp is [linkTAM17076[/link]
£156.36 exc vat
£187.63 inc vat
In stockRecommended usage 1 x C-27H7767 to fit one mini.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm silicon wire and the highest performanc...
100% silcone translucent outer sheath, 8mm lead set with stainless steel wire spiral bound wire giving instant and greater resonance, Kevlar fibre core and a ferromagnetic layer for EMC suppression by Luminition. Top end of ignition lead sets.
Electronic ignition conversion. For points type distributors, fixed or sliding. Negative earth only. Also, available for earlier 23/25D on Negative earth (LU142) or earlier 23/25D with Positive earth (LU142AP12).
ONLY use GCL217 coil for bal...
CSI-Ignition is a fully electronic ignition built in an original housing. You will have to remove the cap to see the difference!|nNeg earth only.
After removing the cap you can select between 16 different curves by using
a screwdriv...
Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.
The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...
Electronic ignition kit to fit 45/59D4 distributors.
Designed to do away with points this is a simple drop in installation to fit into your existing distributor. Also see our range of distributors with built in electronics--BAU1962MS & [lin...
Straight rubber connector pipe. The standard vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could a...
This distributor is for Pre A Plus race or High performance engines and can be fitted with points or LU143A ignition pack can be fitted as an extra
Fitted from 1974 to 1980 for 45D distributors. Ethanol in petrol leans the air/petrol mixture making engines run leaner so see [link]37H8414MS[link].
After lengthy tests we have found nearly all vac units are not to the originals, but with t...
Fited to Lucas type distributors with 45D body in 1974 until 1990 when electronic type that was held on by 2 screws appeared as oppossed to this clip on this type. If you need a new distributor clip-we have them as GDC136CLIP.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
A Plus Electronic Ignition distributor with vac unit, modified to our spec in UK to give best performance on any minis with std to 276 camshaft profile.
Ideal for our EVOLUTION001 camshaft
Brand New distributor complet...
Rotor arm for all A series electric distributors when points are not fitted, except for turbo. The distributor cap for this rotor arm is GDC156.
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.