£82.50 exc vat
£99.00 inc vat
In stock
Ideal for our EVOLUTION001 camshaft
Brand New distributor complete with electronic conversion already fitted.
A PLUS ONLY- IDEAL if contemplating a mild camshaft change at later date.
Having tried and tested all the new suppliers of the imported but british built distributors we now have ours all individually built and tested for the following reasons-
They are unable to advise what curves they have in them as we rarely found them the same.
The base plate would stick and alter the curves sometimes jamming in full advance.
Difficult to get them to run correctly when using a timing light.
The rotor arm and dog at bottom of shaft often found out of phase and so rotor arm in wrong position in relation to the point at where the spark fired so timing way out.
Rotor arm hard up against the carbon bush in top of distributor cap causing the cap to burn away in middle. Pay a little more for Mini Spares quality and peace of mind.
Should be used with GCL143 coil.
Replacement service items for this are:
Cap GDC136
Rotor arm GRA2114
Distributor drive spindle if required is 12G3560
Distributor clamp plate is TAM1671
Bolt for clamp is TAM1706
£82.50 exc vat
£99.00 inc vat
In stockRecommended usage 1 x C-27H7701 to fit one mini.
the bolt that holds distributor clamp TAM1671 in the block on A Plus engines
now obsolete use 3/8"unf bolt with thread length of 1"
This is the standard non ballast coil as used on the late Mini with factory electronic ignition for use with 65D distributor.0.9ohms.
GCL143 was the Genuine Rover part fitted part on 1275cc from 1990.
0.9ohms
GCL2...
Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles
Brand New distributor complete with electronic conversion already fitted.
A PLUS ONLY
Replac...
Electronic Ignition distributor, modified to give better performance on any minis with 310/315 race camshaft profiles.
Brand New distributor complete with electronic conversion already fitted.
A PLUS ONLY
Replacement servi...
Replacement module for Minispares Evolution distributors. Black wire to "C" and red wire to "B" terminal.
100% silcone translucent outer sheath, 8mm lead set with stainless steel wire spiral bound wire giving instant and greater resonance, Kevlar fibre core and a ferromagnetic layer for EMC suppression by Luminition. Top end of ignition lead sets.
Pre A plus Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles
Brand New distributor complete with electronic conversion already fitted.
PRE A PLUS
<...
Pre A Plus Electronic Ignition distributor with vac unit, modified to our specification in the UK to give best performance on any minis with std to 276 camshaft profile.
Brand New distributor complete with electronic conversion already fitt...
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
best plug for 12g295 head as fitted to 998 cooper--for tuned head use B7ES.
this is good for any head where a lot has been machined off-flat top pistons.
Set of 4 ignition leads from the original supplier to Unipart, suitbale for all twin point minis 1997 onwards
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
NEGATIVE EARTH ONLY..Reproduction CONTACTLESS Distributor suitable for modern day fuels for 850 and 998cc pre 1974 with upgraded rotor arm "Negative earth only". A worn out distributor can cost you both performance and economy. Precise spark timing ...
Electronic Distributor for any standard A+ 998cc. Negative earth only.
From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...
Coil bracket fitted to end stud of cylinder head,clutch end for coil to mount on as fitted 1969-94-MK3 on. This has been made to the original specification with the welded lug nuts rather than the cheaper method of having just plain holes to take a b...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
Electronic Ignition distributor, with vac unit modified to give better performance on any minis with 285/286/296 camshaft profiles
Brand New distributor complete with electronic conversion already fitted.
A PLUS ONLY
Replac...
Fitted from 1990 to 1275CC Cooper with HIF44 carburettor.
See RTC3993 for HIF38 carburettor 1275 cars
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.