£159.12 exc vat
£190.94 inc vat
In stock
For best performance and modern day fuel/camshafts and tune we advise our electronic evolution version C-27H7698
Distributor drive spindle if required is 12G3560
Distributor clamp plate is TAM1671
Bolt for clamp is [linkTAM17076[/link]
£159.12 exc vat
£190.94 inc vat
In stockRecommended usage 1 x ALDONYPLUS to fit one mini.
The all new 123 Electronic distributor is now available at Minispares. Featuring 16 ready programmed switchable advanced curves built in as standard, a must for any mini with a worn distributor. Full instructions are included with the system. For any...
A Plus Electronic Ignition distributor with vac unit, modified to our spec in UK to give best performance on any minis with std to 276 camshaft profile.
Ideal for our EVOLUTION001 camshaft
Brand New distributor complet...
This is a race or high performance disributor for A Plus engines and can be fitted with points or LU143A ignition pack can be fitted as an extra
Distributor drive spindle if required is 12G3560
Distributor clamp plate...
Electronic ignition kit to fit 45/59D4 distributors.
Designed to do away with points this is a simple drop in installation to fit into your existing distributor. Also see our range of distributors with built in electronics--BAU1962MS & [lin...
original Lucas type 2 piece contact set made for the non vacuum type distributor fitted to original Cooper S with a stronger 32oz spring. This is the best quality set by far available that you can trust, although there are cheaper sets on the market...
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
Best on the market, sports coil-Not Lucas. A standard coil can only do so much, and when compression is raised (as in most high performance engines) or improper fuel mixtures occur something better is needed. This sports gold coil with proven origina...
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
This is the standard non ballast coil as used on the late Mini with factory electronic ignition for use with 65D distributor.0.9ohms.
GCL143 was the Genuine Rover part fitted part on 1275cc from 1990.
0.9ohms
GCL2...
BPR6E factory fitted but this is the later NGK plug.
NGK has superceeded this plug to a BPR7EIX
100% silicon insulation, silicon coated suppressed conductor,braided glass reinforcement,increased working temperature 0f minus 50C to +300 degrees with improved resistance to damp and water, great fitting and spiral bound wire giving instant and gre...
Also see 8B12398 which also includes coil cover sleeve in stainless steel.
A higher compression engine should have a colder spark plug. The engineers explain that it has to do with flame temperature and overheating the plug. I know from experience that my race engine will melt a street plug. Choose from the following NGK pl...
100% silcone translucent outer sheath, 8mm lead set with stainless steel wire spiral bound wire giving instant and greater resonance, Kevlar fibre core and a ferromagnetic layer for EMC suppression by Luminition. Top end of ignition lead sets.
Introduced by the factory to erradicate water getting to the electric coils causing breakdowns this was used up until they introduced the plastic engine protection shield but many owners still played safe and fitted one anyway.
Made in plast...
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm silicon wire and the highest performanc...
Timing cover front plate and tensioner plate bolt and washer kit. Comes with all parts to fit the cover except for the counter sunk screws if fitting a duplex kit (our duplex kits all come with these).
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
This kit of head studs is the best available for road and lightly tuned engines. See the C-AHT280 set for highly tuned engines.
The material spec is alloy steel heat treated to 75 tensile tons per square foot minimum and finish...
You should replace the camshaft bearings every time the block goes to the machine shop. These bearings fit all late model 1275cc blocks (the ones without tappet covers on the back) It's almost too simple and thus often overlooked during a rebuild. Ca...
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.