(195,00 €) £195.00 exc vat
(234,00 €) £234.00 inc vat
Special order
Usually ordered for customers requirements as these are very rare models.
This panel has no brake cooling cut outs on corners,wheras later models 1964-75 had brake cooling cut outs on corners,use 14A9566 or for rubber mounted subframe from 1976 on see AAM1106
This good reproduction is the only panel available to allow you to restore your car easily.It is a modified saloon panel with grille slat panel welded in.
We sell 10-20 per annum and all the trade and mini owners use this part--maybe because there is no option but they fit fine and once fettled/filled and sprayed up they really look good.
The slatted grille section part is available as 14A6480G but will need cutting down to fit to a saloon panel which is the only alternative and how these panels are created.
(195,00 €) £195.00 exc vat
(234,00 €) £234.00 inc vat
Special orderRecommended usage 1 x 14A6480 to fit one mini.
Non Genuine for the Pick-up and Van with a slat type fixed grille as a trademark for Mini commercial type vehicles originality.
This good reproduction is the only panel available to allow you to restore it easily.It is a modified saloon pan...
Non Genuine for the Pick-up and Van 1964-75 with a slat type fixed grille as a trademark for Mini commercial type vehicles originality.
This panel has the brake cooling cut outs on corners.
Earlier models 1961-64 had no cooling cut...
Floor pan for Mini van/estate with no x member for remote change gearbox. Non Genuine. For saloon see 14A6491
picture is just to show what you get but bulge on centre tunnel for starter button appears to be on wrong side as this...
Small bracket under the front bumper lip to hold the number plate, sold singly.
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to.This is the left hand pane wing with radiator vent slats but not ...
For vehicles with external hinges and sliding type windows this is a full inner front wing with the wheel arch panel. The panel is what that the outer A panels for the hinges attach to. This is the right hand panel made by Heritage but not 100% perfe...
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
Fits round tunnel cars. Approximate location of the vertical, forward wall is 17.5 - 17.75 inches back from the crease in the floor where the floor bends upward under the pedals. The forward wall lines up just forward of the front portion of the exte...
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
For Minis with sliding windows and external door hinges These genuine R/H outer A panels fit over the extra inner panel which have brackets on to reinforce the exterior hinges. If the outside one is rotten you can guarantee the i...
The left side inner fender of the MKI/2/3 pre 1975 Mini should have a metal cowling to focus the air from the radiator to the wheel well. The almost square cowling is spot welded to the inner fender and has the tabs on it that in turn hold the rubbe...
For Minis with sliding windows and external door hinges These genuine L/H outer A panels fit over the extra inner panel which have brackets on to reinforce the exterior hinges. If the outside one is rotten you can guarantee the i...
non genuine oversill MK1/2 van floor profile R/H with 4 flute vents
see MS58R for 6 flute type side, wide type
the rear lower NON genuine corner section of the rear valance on vans.estates.travellers and pick ups L/H --See MS23 for centre section
the rear lower non genuine corner section of the rear valance on vans.estates.travellers and pick ups R/H---See MS23 for centre section
non genuine oversill MK1/2 van floor profile L/H with 4 flute vents see MS58L for 6 flute vents
complete tailgate for the mini pick up from genuine tooling but less the hinges
For minis with sliding windows and external door hinges.
This is the inner hinge panel with the brackets on to reinforce the areas where the hinges sit. You will require the outer panel also 14A6901 for R/H and 14A6902<...
The rear centre valance section for all vans, pick ups and estates. The corner
pieces of this valance are available separately as 14A6908/9
The Heritage produced front wings (fenders) for the Mini are the original with
correct round hole for headlamp. They fit. The proper gauge metal and original tooling ensures that even the novice body man can make them work great. Cars regist...
For minis with sliding windows and external door hinges.
This is the inner hinge panel with the brackets on to reinforce the areas where the hinges sit. You will require the outer panel also 14A6901 for R/H and 14A6902<...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.