(18,00 €) £18.00 exc vat
(21,60 €) £21.60 inc vat
In stock
(18,00 €) £18.00 exc vat
(21,60 €) £21.60 inc vat
In stockRecommended usage 2 x 27H5981A to fit one mini.
This plastic bowl kit includes the inner rim to hold your light unit and will obviously not rust like the old originals. You will need a headlamp outer rim so why not fit our own developed stainless steel variety which is cheaper than even chrome bud...
Headlamp bulb for the 700 series LHD and for Cibie.Sold individually
A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...
Made in the UK. Correct fitting stainless steel type with screw and washer at a special low price for any Lucas or Wipac headlight including injection cars.
A headlight trim ring is only the starting point of a good looking car, but you have...
Almost any screw will hold the chrome headlamp bezel on, but only one is correct! These screws are stainless steel and will never corrode plus they have the little rubber washer on the backside so that the screw will not fall out when trying to fit ...
Originally for cars from 1996 on with depth of 16.3mm this better quality item will fit all minis but the 18mm deep type 515218A is corrrect for earlier cars with the original lucas half inner metal bowl.
This has all the lugs t...
These are for Left had drive L/H/D. See S4698B for Right hand drive R/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special...
Pop rivet for fixing the headlamp bowl to the wing. Great for MS14 metal bowl but be careful if using on plastic bowls
Gasket/seal for all 1997 on mpi headlamp bowls (self levelling type).
A single plastic headlamp bowl only, to accept the levelling motor and rim for all twin point (1997 onwards) Minis plus some export SPI models.
For wipac quadoptics-replacement bulb holder for lamps also supplied in kit.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. The halogen headlamps have very bright 55/60 watt bulbs. Their special lens gives g...
The best chrome type available with screw and washer.
A headlight trim ring is only the starting point of a good looking car, but you have to start somewhere. Sold singly 2 required per car. These are the original type chrome over solid bras...
These are for Left had drive L/H/D. See S4698B for Right hand drive R/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special...
Single replacement light unit for the Left Hand drive kit S4699B with right hand dip.
lamp part only, does not include the rubber cover, bulb or side light part
These are R/H/Drive, see S4699B for L/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special lens gives good long range visi...
If your rusted old headlight bucket is getting to you, don't waste time trying to salvage it when new metal reproduction metal buckets are AVAILABLE.
With a headlamp rim fixing bracket 37H7421 attached
Whether you are ...
The headlamp bucket is isolated from the body with these rubber seals/gaskets.
Headlamp sundries kit.
Includes two adjuster screws, plastic nutserts, pullback spring. Two kits are required per car.
A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...
This is the complete lamp including the self level motor with plastic backing bowl as fitted to late injection cars and German/Japan spec vehicles (will require wiring)
This plastic bowl kit includes the inner rim to hold your light unit and will obviously not rust like the old originals. You will need a headlamp outer rim so why not fit our own developed stainless steel variety which is cheaper than even chrome bud...
These stainless steel peaks fit under the headlamp rim to give that old 60s style again.
This is the wiring required if you have side repeater lamps on your front wings including bulb holder, grommet and connectors LESS the bulb. The large grommet that sits in the inner wing where the wires go through is YML10654. sold indiv...
rear stop and tail lamp for early BMc cars with red plastic lens.
Also stocked is a white lens and single filament bulb equivalent for use as reverse light on kits cars and Mokes as CHM13REVERSE.
Resistor for AFU3389LED and AFU3389WLED, this is needed to enable the lamps to function properly. Sold in pairs.
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.