ROCKER SPACER KIT FOR 2012 ON 8 PORT ROLLER ROCKER...
C-AEG394

(12,00 €) £12.00 exc vat

(14,40 €) £14.40 inc vat

In stockIn stock

(12,00 €) £12.00 exc vat

(14,40 €) £14.40 inc vat

In stockIn stock

Recommended usage 1 x C-AEG394 to fit one mini.

People also bought products
EXHAUST MANIFOLD GASKET 8 PORT HEADS ONLY
C-AHT380

Exhaust manifold gasket for Arden 8 port head.

(3,00 €) £3.00 exc vat

(3,60 €) £3.60 inc vat
EXHAUST VALVE 30.5MM FOR 2012 8 PORT HEADS
C-AHT372

30.5mm(1.2") longer exhaust valve for the 2012 on 8 port head only

for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol--For earlier heads see C-AHT376/7 valves.

The valve size h...

(19,04 €) £19.04 exc vat

(22,85 €) £22.85 inc vat
INLET VALVE 37mm 8 PORT HEAD 2012 on
C-AHT370

37mm(1.457") longer inlet valve for the 2012 on 8 port head only

for use with special guides these are plasma heat treated to eradicate premature wear from unleaded petrol



3.933" 99.898mm long

(19,04 €) £19.04 exc vat

(22,85 €) £22.85 inc vat
HEAD GASKET - RACE 1275-1380/73.5mm MULTI LAYERED ...
C-AHT189

3 layer steel head gasket especially suitable for full race engines up to 73.5mm

bore where it has larger bore holes and considered the ultimate head gasket.

Especially recommended for 8 port heads as it has no fire/compression ring...

(60,00 €) £60.00 exc vat

(72,00 €) £72.00 inc vat
ROCKER LESS SCREW L/H C-AHT446
C-AHT447LEFT

Single l/h rocker less screw

not sure what side you require? --By holding the rocker the correct way up with the adjuster screw end facing you the roller will be biased either to the right or the left which denotes the side required.

(14,85 €) £14.85 exc vat

(17,82 €) £17.82 inc vat
MANIFOLD GASKET INLET / EXHAUST
AJM601

Manifold gasket fitted to all A series pre 1992 except Turbo which had a reinforced exhaust ports GUG704063MG and SPI from 199. From 1991 on a new better gasket with reinforced exhaust ports and backing was fitted GUG704053MG

(0,96 €) £0.96 exc vat

(1,15 €) £1.15 inc vat
ROCKER SPACER KIT WITH SPACERS AND SHIMS
C-AEG392

Mini Spares spacer kit re-designed in 2005 for correcting rocker alignment.

This kit has been produced to help rocker pad and valve stem alignment plus reducing friction. The standard springs can be replaced with this special kit of 3 spacer...

(13,07 €) £13.07 exc vat

(15,68 €) £15.68 inc vat
VALVE STEM TOP HAT SEAL A PLUS (Single)
ADU4905

As an engine wears, the clearance between the valve stem and guide increases; as this gets beyond tolerances the car will tend to smoke under deceleration (when you take your foot off the throttle). Good valve stem seals will allow for greater wear b...

(0,54 €) £0.54 exc vat

(0,65 €) £0.65 inc vat
ROLLER TIP 1.5 WITH LARGER SHAFT
C-AHT446EVO

Roller-tip rocker assembly. 1.5 Hi-Lift for 1275cc big bore engines only.

Craddle type with larger upgraded shaft size to improve rigidity.

Ensure tightening down all posts equally to eliminate stress fractures on shaft.

(320,83 €) £320.83 exc vat

(385,00 €) £385.00 inc vat
TIMING COVER OIL SEAL ALL PRE 1992
88G561

Genuine Mini Spares Original black timing cover oil seal for all A series until the introduction of a new type of lip seal introduced in 1991 mainly for injection engines, when they changed to LUF10006--albeit many owners fit this not kn...

(1,80 €) £1.80 exc vat

(2,16 €) £2.16 inc vat