(43,55 €) £43.55 exc vat
(52,26 €) £52.26 inc vat
In stock
(43,55 €) £43.55 exc vat
(52,26 €) £52.26 inc vat
In stockRecommended usage 1 x CK721 to fit one mini.
Metric & Imperial offset feeler gauge set, ideal for setting tappet clearnace, primary gear end float etc. Offset for ease of use.
Imperial: .005/.006/.007/.008/.009/.010/.011/.012/.013/.014/.015/.016/.017/.018/.019/.020/...
3/8" 6 point shallow AF/Imperial Socket set
Sizes 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16"
This tool bolts where the starter motor fits to lock the flywheel in place when trying to remove the flywheel bolt/crank pulley etc.
Classic Castrol oil can with flexible spout and thumb pump.
Three arm oil filter wrench ideal for changing the spin on filters on Mini's. Comes with adaptor for 3/8" or 1/2" drive, suitable for filters from 65-120mm diameter.
Mini Spares offer this tool with a MSF166 filter for nearly no...
Plain white with white backing aftermarket sun visor as fitted to Mk3 models 1977-92 which were thinner than Mk1 for safety crushing requirements. Although not standard for earlier models will fit cars from December 1965. Check out the special clips ...
Cream with crackle finish sun visor fitted as standard from December 1965-69 but will fit Mk3 on if required. With mirror for passenger side. For a car set of clips see SV2021
Mk1/2 1965 on cream crackle SV2017C
Mk3 196...
Cream colour crackle finish sun visor as fitted from december 1965 onwards. Will fit later cars if required. Drivers side without mirror.Check out the special clips to hold these visors as they are sold seperately in car sets only as SV2021<...
1/2" hex key socket needed when using our upgraded crank pulley bolt C-AHT147, 1/2" drive.
CV fitting tool, designed to assist with the correct fitting of CV joints, wheel bearings or drive flanges, as specified in the Haynes workshop manual. The wheel bearing should be torqued to the specified setting using this washer, and then removed a...
A series crankshaft tap in 5/8 x 16 tpi Whitworth form, used for both ends of the crankshaft.
Complete car set of roof lining rods, comprising of 1 Red, 2 White, 1 Black, 1 Blue and 1 Yellow
number 1 with red ends is EEB100060
number 2 and 3 is white ends are both EEB100070
number 4 with black ends is EEB100080
...
Sykes Pickavent 21mm spark plug socket, 3/8" Drive
Roll pin punch for removing RPS1416 roll pin from the gear selector mechanism.
These headlinings are held in by different shape/length rods which are NOT included but we do include the rear corner side sections between the rear side window and backlight which many poor copies do not
the rods are
red end x1...
This chromed bracket is to secure the early Mini sunvisor with the central location.
1959-64 visors had one central hinge and in October 1964-65 they fitted a sunvisor with a hinge one end and clip fixing the other-this is when the first pla...
This was the first style of sunvisor pad with central pivot point in cream crackle finish used on the early Minis.Some very early minis used pale grey for std but all Supers had crinkle finish cream to match headling. For this period the Cream Crackl...
Ideal for solving the problem of fitting extra speaker's, this speaker board is simple to fit, and well finished speaker holes are oval 6"x9"
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.