£26.10 exc vat
£31.32 inc vat
In stock
Mini Spares offer this tool with a MSF166 filter for nearly nothing so see this part when ordering GS102440
£26.10 exc vat
£31.32 inc vat
In stockRecommended usage 1 x TOOL09 to fit one mini.
Mini Copper Sump Drain Plug Washer, also will fit the oil transfer pipe block fitting on Pre 1992 Blocks.
Genuine Minispares spin on oil filter from the original suppliers as designated and approved by Rover/Unipart until 2014 when parts quality selection changed.
Same manufacturer and item as GFE443 but with our livery on so you know you are g...
Tool to remove the oil filter and a genuine spin on Mini Spares filter pre MPI cars, as sold by Rover and Unipart but in our livery until their closure.
Tool to remove the oil filter and a genuine spin on Mini Spares filter pre MPI cars, as sold by Rover and Unipart but in our livery until their closure.
Metric & Imperial offset feeler gauge set, ideal for setting tappet clearnace, primary gear end float etc. Offset for ease of use.
Imperial: .005/.006/.007/.008/.009/.010/.011/.012/.013/.014/.015/.016/.017/.018/.019/.020/...
Imperial & Metric spanner set ideal for completing most tasks on your classic Mini, these are mirror polished spanners.
Contents: Bi Hex x Metric combination spanners 6, 7, 8, 9, 10, 11, 12, 13, 14, 17, 19mm and Stubby 10, 11, 12, ...
3/8" 6 point shallow AF/Imperial Socket set
Sizes 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16"
1/4" 6 point deep AF/Imperial Socket set
Sizes 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2" AF
1/4" 6 point Shallow AF/Imperial Socket set
Sizes 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2" AF
This tool bolts where the starter motor fits to lock the flywheel in place when trying to remove the flywheel bolt/crank pulley etc.
1/2" hex key socket needed when using our upgraded crank pulley bolt C-AHT147, 1/2" drive.
CV fitting tool, designed to assist with the correct fitting of CV joints, wheel bearings or drive flanges, as specified in the Haynes workshop manual. The wheel bearing should be torqued to the specified setting using this washer, and then removed a...
A series crankshaft tap in 5/8 x 16 tpi Whitworth form, used for both ends of the crankshaft.
Roll pin punch for removing RPS1416 roll pin from the gear selector mechanism.
This bag is made out of "Hardura" which is a heavy PVC with a felt backing laminated to it. When sewn up it will hold the Jack & lever and is all held with the tie Straps. Because the bag is made of heavy material it will not wear through unlike plas...
Molybdenum Grease supplied in a 500g tub, suitable for the lubrication of CV joints and any other homokinetic joints.
Multi-Purpose LM2 Grease supplied in a 500G tub.
This grease is suitable for Wheel Bearings, Radius Arms, Upper arms, knuckle joint cups and other regular greasing points.
ESPECIALLY FOR MINIS
This 20-50w semi synthetic oil is produced especially for minis where it needs to lubricate both engine and gearbox parts giving the neccessary coating and protection. Semi synthetic has a long life to 100c with maximum ...
Mineral oil especially formulated for the combined engine and gearbox such as the mini, but for better gearchange etc use MILERS002 except on rebuilt engines where pistons must be allowed to bed in using non synthetic oil. 5 litre bottle.
Se...
This new type suspension cone tool for removing or refitting the rubber suspension cone is METRIC thread only and improved by using a hex(allen)key to screw in and hold the centre spindle. There cannot be many cars left out there with the AF type th...
Spanner for adjusting the jet on silver coloured original jets on HS type carbs
short handle to enable use in tight places such as a mini engine bay.
WILL NOT FIT LATEST BRASS TYPE ADJUSTER NUTS AS FITTED TO REPLACEMENT CARBS SINCE ...
A handy little gadget for fitting the circlip holding the rear wheel cylinder on
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.