£0.79 exc vat
£0.95 inc vat
In stock
£0.79 exc vat
£0.95 inc vat
In stockRecommended usage 3 x AED172 to fit one mini.
This latest type washer with internal seal is used on the oil feed pipe from the block to the filter. One either side of the pipe union. Found on engines from about 1985 on. Sold singly, 2 per car required.
Fits in place of the oil pick up retainer plate on the back of the gearbox this magnetic plug with filter collects metal debris from going back into the power unit but should be regularly cleaned. A non filter type of theis version is available as [l...
Fits in place of the oil pick up retainer plate on the back of the gearbox this magnetic plug filter collects metal debris from going back into the power unit but should be regularly cleaned. Also available as the ultimate is the same item with a bui...
Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
The gasket with the oil suction seal hole fits every mini gearbox case and the other two are for the different case shapes, one for 3 synchro case and one for 4 synchro gearbox case, so choose the one you require. For latest spec Klinger gasket set u...
Actually the concertina dust cover for the rod change oil seal to prevent road debris attacking the seal. See MSSK050 kit when undertaking this job.
Genuine gearbox gasket for the large alloy end cover which also houses the speedo drive pinion for all years of mini. The small gasket on the alloy housing with 2 bolt holes is GUG705564GM and the small pear shaped speedo housing gasket ...
This is the large clutch case gasket that is made to a special thickness.
Many companies who copy these gaskets are not aware that the gasket thickness and consistency is important as it affects the clearance on the idler gear shimming. This...
Genuine Mini Spares green and black upgraded Klinger gasket set. 3 pieces
Has the extra front gasket required for 3 synchro case use
Lower differential housing paper gasket for old magic wand and remote type gearboxes, rod change gearboxes.
Gearbox oil strainer to gearbox internal case gasket and also used on the C-AHT54 special oil pick up pipe. One also sits on the outer plate held onto the gearbox outer casing by 2 screws.
Probably the most used jointing compound used by mini owners for nearly every gasket except the cylinder head. Some late minis used a silicone jointing compound instead of gaskets on the differential, see GAC8000.
for the inspection plate on the front cover of the transmission where the speed cable goes to -it has 2 bolt holes cut out
Often overlooked when doing gearbox rebuilds this seal is very important as it sits in the very bottom of the case and is the source of irritating oil leaks.
The large round metal plug in the bottom of the gearbox is the pivot pin for all th...
Gearbox output shaft housing gasket for all minis except auto.
Sold singly 2 required per gearbox.
Try these GENUINE MINISPARES superseal gearbox output shaft gaskets specially made to try and eliminate leaks.
Sold singly,2 per gearbox
This kit consists of one alloy sleeve with a groove on the outside to locate the O ring, the new "O" ring, a rod seal and a gaiter. To fit the kit simply remove the old gaiter if fitted and then the old oil seal. Fit the sleeve with the "O" ring fitt...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.