MANIFOLD LOCATING RING
12G297

£2.56 exc vat

£3.07 inc vat

In stockIn stock
Locating rings originally made for 12G295 heads with twin carbs to line up the inlet manifold to the inlet ports on the cylinder head it found its way on most twin carb factory produced cars. There is a recess in the inlet port on the head and usually the inlet manifold to take these spacers.

£2.56 exc vat

£3.07 inc vat

In stockIn stock

Recommended usage 2 x 12G297 to fit one mini.
Inlet & Exhaust Manifolds - Qty 2
Inlet and Exhaust manifolds except Injection - Qty 2
Inlet and Exhaust manifolds for Injection Cars - Qty 2

People also bought products

New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the v...

Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket

New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.

These locate better in the valves and easier to control spring heights.

Alloy CNC version of the cylinder head take off 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does

Originally fitted to Minifin rocker covers as standard Rover equipment, it will also fit almost every other rocker cover including our FP26 range and Minispares alloy covers. This improved cap has a large grip and an improved lock system...

Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.

We have no evidence as yet that they last longer but do look good.

See [lin...

Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...

Early Large cotter groove exhaust valve. Most small bore engines seem particularly prone to burning valves, it is highly recommended to replace the exhaust valves when you do a valve job! This 1.0" valve fits most early 948cc, 998cc and 1098cc engine...

We stock a limited range of Paul Ivey developed Rimflow valves for the A-Series.

30.9mm (1.217") diameter exhauste valve for 12G940 large bore casting is oversized to the stock version. Not only can you pick-up performance from...

Special reinforced gasket for injection cars has metal inserts on exhaust ports plus a metal back on the manifold side which makes surface easier to clean when replacing. Often used on Turbo cars when correct gasket is in short supply.


...

This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...

Unlike polished covers, these black powder coated aluminum valve covers don't get that dingy look; simply wipe them and they're clean. (Fins and Mini Spares logo remain cast aluminum finish) And they're made to clear our hi-lift rockers. Available ...

Originally marketed by minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment they were improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. These T b...

Originally marketed by Minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment. These have been improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. Ki...

1992 TO 1996 SANDWICH PLATE. SPI AND CARB MINIS. HAS TAPPED HOLE FOR RAD BRACKET STUD. NO SENDER HOLES. SPI MINIS USE WITH 12G103 TOP HOUSING, CARB MINIS USE WITH PEQ10010(THERMO SENDER HOLE AT FRONT).

PLUG, Cylinder head 2 fitted to 1275cc heads 15/16 mm wide tapered plug

with hole.

Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.

New colour, PB104 bronze guides.Although Silicon bronze valve guides were used for their extremely good wear values, they were very hard and not user friendly when fitting. These valve guides are recommended when using all EN21 4N stainless steel val...