HANDBRAKE FLY OFF KIT
C-AJJ4019

£13.00 exc vat

£15.60 inc vat

Out of stockOut of stock
Kit contains a new pawl and two new rivets, with fitting instructions.

By simply replacing one component of the handbrake lever you can change to "fly-off" operation. This means that you'll have to push the button to lock the lever, otherwi...

£13.00 exc vat

£15.60 inc vat

Out of stockOut of stock

People also bought products

Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.

Genuine AP Lockheed rubber boot

For CLZ409 clevis pin on rear brake levers.

Split pin for common clevis pin list

GFK101 for CLZ409 handbrake levers to cable on rear drum

GFK102 most mini clevis pins exce...

Concave washer for the CLZ549 pin on the quadrant of dry suspension minis.

Pretty alloy handbrake quadrants for those special cars, with an extra 6 cut out holes giving extra lightness. Dry suspension cars pre 1976 only.

Supplied as a pair.

This is a pair of rear brake back plate actuating levers. One Left and One right hand. If you want the rubber gaiters they sit through, order individually as 17H7612

the finest brake pad available for mini 8.4" discs or Sprite/Midget cars.

These are for all forms of competition road use.

A set of split pins are available as GBK1010 or with metal retaining clips as GBK1026

Cooper S 7.5" complete brake disc kit, except for disc shields, with Mini Spares own cast standard calipers. If you want or have 10" wheels this is the kit to convert from drum brakes to discs brakes.

This kit includes every nut bolt and co...

This bracket is the main mounting bracket for the handbrake lever assembly and is welded onto the back of the seat crossmember and to the rear floor section.

Only for Pre rod change cars with twin cable handbrake.

The later type bra...

This bracket is the main mounting bracket for the handbrake lever assembly and is welded onto the back of the seat crossmember and to the rear floor section.

Only for rod change cars with late type single cable handbrake.

the early ...

special shaped nut for handbrake cable at handbrake end



Twin cable use 2A5858

The rubber type grip fitted on handbrakes-

will fit any single cable hand brake from 1976 on

Mk1/2 used 13H5541 thinner plastic type--to fit this to pre 1976 early cars you will need to put lots of sticky tape on the h...

Adjustable original brake proportioning/balancing valve for racers only.

The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...

Pair of vented discs and Mintex GBP258AF pads,one of our best selling brake disc kits. Includes discs[link](GBD496)/link] which are a bargain.Only for carss fitted with vented discs already.

This is not a direct replacement kit ...

From 1989 minis which have the brake servo built into the master cylinder and it is very difficult to work in the engine bay, especialy clutch changes because of the extra room taken up by this dual cylinder. By replacing the 2 metal brake pipes from...

From 1976 the handbrake cable layout was changed, instead of two cable from the handbrake it was changed to one. Front for the saloons GVC2135 is 25" long and the van requires 29.5" long which is available as FAM625. This is...

Set of 4 hoses, 2 front and 2 rear.

Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...

From 1976 the handbrake cable layout was changed, instead of two cables from the handbrake it was changed to one. Front for the saloons is 25" long and the van requires 29.5" long which is available as FAM625. The cable between the wheel...

Cooper S 7.5" complete brake disc kit, except for disc shields, with genuine AP calipers and Tinken bearings. If you want or have 10" wheels this is the kit to convert from drum brakes to discs brakes. See C-AJJ4028MS for kit with our ow...

Same steel braided pipes but includes the clutch pipe for Verto type clutch.



Please be aware the fronts are sided, the deeper threaded hose fits the right hand side, the shallower hose fits the UK passenger side.