Starter safety switch panel with red safety light
MSA336

£16.40 exc vat

£19.68 inc vat

In stockIn stock
On /Off safety swith guard and press starter switch,a red safety light --See MSA337 for extra swith and light, no wiring included.

£16.40 exc vat

£19.68 inc vat

In stockIn stock

Recommended usage 1 x MSA336 to fit one mini.

Alternative products

Make your classic a little bit safer and racier with these rally type ignition switches.One of these mounted on your dash board will allow you to flick the red cover up, click the switch down and then thumb the button to kick the engine into life. Th...

People also bought products

Wiper Swithch MK1/2/EARLY MK3 blade type switch for using to convert to 2 speed wipers when current 2 speed wiper motor is used.

Courtesy switch for MPI minis from 1996 when the wiring was changed from bullet type to spade connection. This is the switch that fitted into the A post to turn the interior light on and off, the earlier switch is no longer available so if you have a...

With an integral push start button built in the solenoid as originally fitted to early minis. The activation of the starter motor starts with the key (or push button in the early cars), but the most important function is carried out by the solenoid....

Rocker switch for all models with front fog lights fitted as standard. Please note the lens colour is now green. 6 pins on the back for plastic loom connector.

Fitted under the bonnet on top of the servo. Relay for the engine management on twin point cars only from 1996-except for cars with air conditioning which use YWB101080.

On /Off safety swith guard and press starter switch,a red and green safety light plus one switch, no wiring included. Plate size 65mm x 135mm.

Rear fog lamp switch with the orange illumination segment for all vehicles fitted with production fog lamps as standard. 3.1cm tall from 1976 on.

Metal plate switch carrier for 5 square type switches.

Mk1 Mini Indicator stalk green lens. Also fitted to other BMC variants such as Morris Minor. See GLB280 for the replacement bulb

IGNITION BARREL TO FIT 13H337 SWITCH. MK1/2/EARLY MK3. ONE BARREL,TWO KEYS

circuit breaker for safety as required in motorsport

The switch has to be accessible from inside and outside the car.The external trigger should be located on the windscren scuttle panel -preferably the drivers side . It should be clearly ma...

Brake light switch for pre 1976 minis with single line brake systems. Fits into banjo bolt (7H7995) located at O/S front brake hose. This switch has a tapered thread. Made by a UK company who suplied parts to Unipart.

For minis ...

Horn push assembly for the Mk1 Austin Mini, Mk1 Austin Mini Cooper and Mk1 Austin Mini Cooper S.

For Morris cars, see 27H6944. This horn push assembly can also be supplied without a centre emblem, see 27H6945

MK1/2/EARLY MK3. 3 position spring loaded type. Comes with barrel.

For barrel only use part number 24G1345.

Headlamp switch fits MK1/2/ earlyY MK3, Toggle type also known as bat handle type, 3 POSITION. BLADE CONNECTIONS.

Used on Rod change gearboxes and fits on the side of the gearlever alloy housing, the locknut is to prevent the switch being screwed in to far. Use 22A1613 locknut.

WIPER SWITCH,FITS MK1/2/EARLY MK3.TOGGLE TYPE.2 POSITION.

Battery cut-off switch. FIA approved

Most race sanctioning bodies require the use of this special (diode protection device) cut out allowing the switching off whilst the engine is running without damaging the electrics. The switch has to be ...

This switch fits under the brake pedal on the floor. See also BMK1903A locknut for this item.

Make your classic a little bit safer and racier with these rally type ignition switches.One of these mounted on your dash board will allow you to flick the red cover up, click the switch down and then thumb the button to kick the engine into life. Th...