(¥0) £0.23 exc vat
(¥0) £0.28 inc vat
In stock
individually
(¥0) £0.23 exc vat
(¥0) £0.28 inc vat
In stockRecommended usage 20 x BHA5097 to fit one mini.
plastic heater knob that pushes on the end of the control lever on Mk1/2 heaters. one required per car.
bracket for boot board R/H on 7.7 gallon tank and on both sides for 5.5 gallon tank when 165 tyres fitted
L/H BOOT BOARD BRACKET FOR 7.5 GALLON TANK AND 165 TYRES.
'Walnut Burr gear lever knob.
Standing 3.5 inches tall with a shape that is comfortable to the hand it really makes a statement. the old original type with a logo has been made obsolete owing to royalty and intellectual agreements held by Ro...
The rubber type grip fitted on handbrakes-
will fit any single cable hand brake from 1976 on
Mk1/2 used 13H5541 thinner plastic type--to fit this to pre 1976 early cars you will need to put lots of sticky tape on the h...
Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.
Also suitable for Twin Point indicator fixings.
Universal set of 9 piece carpet which requires the gear lever hole to be cut
depending on type you have. With edge beading as appropiate where required these quality pile are great value. Made to fit any saloon they are perfect fit for rod c...
127cm long and 43cm wide this is enough leather cloth trim that fitted S and deluxe models on the upper and lower facia plus the winscreen A posts. Fitting instructions are included but no glue.
This wire strap type was fitted from 1974 as standard, but this will fit all minis from 1959 to 1995. 36cm x 29.5cm
Reproduction gear lever gaiter for all remote control type gearboxes with the short gear lever by the driver's seat. The metal retainer for this gaiter is 14A9942. These were fitted until the introduction of the rod change type [link]CZH...
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI to Mk3 Minis pre 1976 and on the accellerator pedal from 1976 -1996.
Brake and clutch pedal pads contribute to comfort and safety. They also add that final touch to a nice interior. GPR104 fits brake and clutch pedals of MkI & MkII Minis up to 1976 and the throttle pedal on post 1976-1996 models.
The special pointed shape buffer locates against the boot board of Cooper S and variants where a factory type boot board is fitted.
These special hoses are for all sliding window type doors to drain the water away from the channels. The thin end of the hose slides into the bottom tube to ensure water goes out and cannot leak into the bottom of the door and the top slides over the...
Lower moulding clip for wind up window mouldings..4 PER SIDE required but sold singly-Fits CZH1666/7 and PAM1014/5
Also used for 24A1169 glove box moulding MK1/2.
Four tailor made felt pieces to fit in the segments between the bonnet strengthening webs to allow maximum under bonnet clearance.
See FELT860 for spray adhesive. These are about 1cm thick and the original very thick sound dea...
Chromed version of the standard demist vent on early cars where the ashtray is
mounted in the top and middle of the metal facia. Not for later cars with large
padded windscreen rails and ashtray in the front such as Mini Clubman and...
Also used for other trim areas this clip holds the vinyl or fabric of the seat covers to the metal framework.This part has larger D shape and claw spikes but if you want the smaller D shape and claws for headlining and rear seat covers see[link]14A80...
Fire retardent felt with correct cut outs for MK3 cars for the mini firewall just behind the carb and air cleaner full width of the panel see FELT860 for spray adhesive.
Seat Spacers.
If you think you are too tall for the Mini. These brackets allow you to really stretch out.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.