(¥56) £55.89 exc vat
(¥67) £67.07 inc vat
In stock
(¥56) £55.89 exc vat
(¥67) £67.07 inc vat
In stockRecommended usage 1 x C-GRH1465 to fit one mini.
Genuine Mini Spares own product,this top hose is a real large bore hose that goes right across the engine so you cannot miss it on your twin point injected car with a front mounted radiator.
Try the C-GRH1465 silicon hose if you...
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
Spring clip for securing the top hose on MPI front mounted radiator models, now in stainless steel.
Spring clip for securing the top hose on MPI front mounted radiator models.
Silicone heater hose, 39")1metre) for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1984 cars.
Radiator hose kit for all mpi Minis. This kit has top and bottom radiator hoses all in shiney red Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer who never wants a failure or the...
Radiator hose kit for all spi Minis. This kit has top and bottom radiator hoses and 2 lengths of heater hoses…all in shiney blue Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer w...
Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.
Long lasting silicon by pass hose between cylinder head and water pump.
These are easy to cut and slide on easier than the old conventional rubber type.
It has been made this length to fit 1275cc engine,which used the longest hose.<...
Water hose pipe clip for the GRH1140 top hose and twin point injection cars which had larger hoses fitted .This clip will wind down to fit most radiator hoses if required.
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
Unless your're heavily into the concours scene you'll love these hoses. These silcone hoses will withstand higher temps and pressures and will last virtually forever. Made to fit 1275cc cylinder head the length is made to cover 1275cc engines includi...
Silicone heater hose, 42" for cars with the original heater valve bolted on the cylinder head.
Cars after 1976 require one of this 42" length and one C-GRH1006 39" length.
Cars from late 1984 to 1988 had 5/8" outlets on...
Silicone heater hose, 39" for cars with the original heater valve bolted on the cylinder head. Pre 1976 cars can use 2 0f these lengths, commonly known as 1/2" bore heater hose. Also see C-GRH1007 for the longer 42" hose on 1976 on model...
Hose clip for 5/8" heater hose and used to locate 3/4" diameter anti roll bar in our C-AJJ4008 kit.
Clear plastic windscreen washer tubing sold by the metre only. This is the larger size and was known as 1/4" bore because GWW201M is 1/8" bore. This hose is actually now known as 4.8mm which is nearer 3/16".
this was known as 1/...
The original type pk screws for the original 2 piece rad cowlings pre 1974.
6 required
Special bracket for holding the front mounted radiator on twin point injection cars from top of front panel
Unless you're heavily into the concours scene you'll love these hoses. These silicone hoses will withstand higher temps and pressures and will last virtually forever and if you ever had to replace a lower hose you'll appreciate that last fact. These ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.