£8.80 exc vat
£10.56 inc vat
In stock
£8.80 exc vat
£10.56 inc vat
In stockRecommended usage 1 x PEU102380 to fit one mini.
Spring clip for securing the top hose on MPI front mounted radiator models, now in stainless steel.
Spring clip for securing the top hose on MPI front mounted radiator models, now in stainless steel.
Radiator hose kit for all mpi Minis. This kit has top and bottom radiator hoses all in shiney black Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer who never wants a failure or t...
Silicone heater hose, 42" for cars with the original heater valve bolted on the cylinder head.
Cars after 1976 require one of this 42" length and one C-GRH1006 39" length.
Cars from late 1984 to 1988 had 5/8" outlets on...
Silicone heater hose, 39" for cars with the original heater valve bolted on the cylinder head.
Pre 1976 cars can use 2 0f these lengths, commonly known as 1/2" bore heater hose. also see C-GRH1007 for the longer 42" hose on 1976...
Water pump fitting kit for models without bypass facility, includes new bolts, washers and superseal gasket.
A much better looking under bonnet item this bright blue hose will last much longer than rubber -made in silicon-will fit original plastic type radiator outlets or latest metal type outlets.
Original mini half inch bore heater hose cut to metre lengths as required.
The MK1/2 had one hose 35" and one at 16" long, MK3 had one 35" and one at 29".(These are all maximum lengths).
Please note MK4 1976 on some had 42" heater t...
Water hose pipe clip for the GRH1140 top hose and twin point injection cars which had larger hoses fitted .This clip will wind down to fit most radiator hoses if required.
Real Kevlar stranded hose,2 year guarantee-the only true Kevlar threaded hose available where you can see the strands, it is made for longevity and low heat transfer making this the best selling bottom hose in the market.
The built in proper...
Hose clip for 5/8" heater hose and used to locate 3/4" diameter anti roll bar in our C-AJJ4008 kit.
Clear plastic windscreen washer tubing sold by the metre only. This is the larger size and was known as 1/4" bore because GWW201M is 1/8" bore. This hose is actually now known as 4.8mm which is nearer 3/16".
this was known as 1/...
In 1974 the mini changed from a two piece to a one piece cowling. These bolts ONLY fit the two piece pre 1974 cowling.
Stainless steel version of the upper radiator bracket fitted from 1990 -1996 on cars with one piece rad cowlings when engines were fitted with a sandwich plate under the thermostat housing which made them taller.
Special bracket for holding the front mounted radiator on twin point injection cars from top of front panel
1275cc engine top hose in Rubber with Kevlar reinforcement.
Kevlar is a high tech aramid fibre produced by Dupont co in USA.
It is longer lasting, stronger with less heat transfer and wear resistance.
Not only does this hos...
Heater hoses and expansion tank hoses are mostly 5/8" from 1985 on so check the bore size as some were actually 1/2" hose with flared ends of 5/8" you will need to use a restrictor pipe MOC210.
Original 5/8" rover hoses were 1"(...
Genuine Mini Spares own product,this top hose is a real large bore hose that goes right across the engine so you cannot miss it on your twin point injected car with a front mounted radiator.
Try the C-GRH1465 silicon hose if you...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.