£13.43 exc vat
£16.12 inc vat
In stock
£13.43 exc vat
£16.12 inc vat
In stockRecommended usage 1 x PCU103110SS to fit one mini.
Special bracket for holding the front mounted radiator on twin point injection cars from top of front panel
Special bracket for holding the front mounted radiator on twin point injection cars from top of front panel
Original 7/16" spring type hose clip as used on later cars (approx 1990 on) for some radiator hoses and fuel lines.
Spring clip for securing the top hose on MPI front mounted radiator models, now in stainless steel.
Spring clip for securing the top hose on MPI front mounted radiator models.
Silicone heater hose, 39")1metre) for cars with the inline type heater valve or a straight take off on the cylinder head as fitted to post 1984 cars.
Radiator hose kit for all mpi Minis. This kit has top and bottom radiator hoses all in shiney black Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer who never wants a failure or t...
Radiator hose kit for all mpi Minis. This kit has top and bottom radiator hoses all in shiney blue Silicone that should last forever and not degrade with heat, time and environment. This kit is ideal for both the racer who never wants a failure or th...
Red Silicon Top Radiator Hose
Unless your're heavily into the concours scene you'll love these hoses! These silcone hoses will withstand higher temps and pressures and will last virtually forever!Made to fit any 850/998/1100cc minis plus HI...
Water hose pipe clip for the GRH1140 top hose and twin point injection cars which had larger hoses fitted .This clip will wind down to fit most radiator hoses if required.
Silicone heater hose, 39" for cars with the original heater valve bolted on the cylinder head. Pre 1976 cars can use 2 0f these lengths, commonly known as 1/2" bore heater hose. Also see C-GRH1007 for the longer 42" hose on 1976 on model...
Hose clip for 5/8" heater hose and used to locate 3/4" diameter anti roll bar in our C-AJJ4008 kit.
True Kevlar strands with 2 year guarantee.Fitted as standard in some of the hot countries before heaters became standard fitment this hose has the elbow joint missing that connected to the half inch heater hose. A favourite for racers and competion e...
Upper radiator hose for 850/998/1098cc Mini Mk2. This hose is shorter than the original Mk1 radiator, but fits all curent radiators where the radiator outlet is positioned 1-1.5" in from the outer edge.
Special bracket for holding the front mounted radiator on twin point injection cars from top of front panel
Heater hoses and expansion tank hoses are mostly 5/8" from 1985 on so check the bore size as some were actually 1/2" hose with flared ends of 5/8" you will need to use a restrictor pipe MOC210.
Original 5/8" rover hoses were 1"(...
Genuine Mini Spares own product,this top hose is a real large bore hose that goes right across the engine so you cannot miss it on your twin point injected car with a front mounted radiator.
Try the C-GRH1465 silicon hose if you...
Engine mounting bracket on the end of the gearbox which also holds the radiator support bracket. This fits to the alloy bracket 12G1318 on the front cover of the gearbox.
MPI only. 3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump. Mini Spares procured product as original Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller as used by Jaguar and Aston Marti...
3 YEAR GUARANTEE-UK made.Large impeller higher capacity water pump with top quality die cast body . Mini Spares procured product as the original superb Rover Airtex tooling has been scrapped.
Fitted with a PPS, glass filled plastic impeller...
m6x10 bolt--ideal for radiators with metric fittings (6 required for rads)
original imperial radiator screws were SH604031 or PK type were ARA1117
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.