FRONT PANEL MINI 1997->2000 MPI (FRONT MOUNTED RAD...
ASJ360070

($195.00) £195.00 exc vat

($234.00) £234.00 inc vat

In stockIn stock
For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet opening location fittings. Also has holes for 4 extra lamps fitted as standard

($195.00) £195.00 exc vat

($234.00) £234.00 inc vat

In stockIn stock

Recommended usage 1 x ASJ360070 to fit one mini.
Saloon and Front Ends - Qty 1

Alternative products

Reproduction version os ASJ360070. For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet fittings.

People also bought products

L/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3

this is a genuine heritage part.

R/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3

this is a genuine heritage part.

This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.

On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...

Reproduction version os ASJ360070. For the twin point only as it changed shape to accommodate the front mounted radiator and different bonnet fittings.

Aftermarket version of the L/H floorpan for 1991 on cars.

This floor was made stronger with smaller heel pad area to prevent vibration and rust and will fit any Rod change gear shift mini but was introduced on the first injection cars in 199...

A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.

Experience has shown its easier to fit the genuine panel HMP441001 al...

You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...

Inner front L/H wing with the A panel and door stiffener check strap panel attached for ease of fitment and alignment.This has the large round hole for the fan as fitted from 1991on

You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...

1970 on, cars with internal hinges and wind up windows

This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section

THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7

This panel has mounting holes for later models facia crash panel. These holes will require blanking for true originality on earlier models without the facia pad

Genuine front panel fits all pre rubber mounted subframe cars .

The early pre 1964 Mk1 had different shape lower valance without cut aways under the bumper apron but this genuine panel will fit all.

There is a good aftermaket panel...

Inner front R/H wing with the A panel and door stiffener check strap panel attached for ease of fitment and alignment. Always check the bonnet prop bracket location as they changed.

See ALA5661MS for an upgraded thicker and best fitting aftermarket L/H A panel-all the local bodyshops fit this.

Known as an A panel this is for all wind up widow type cars with internal door hinges and is single skin as opposse...

This late front panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once. Early Minis can use [link]MS4...

Aftermarket version of the R/H floorpan for 1992 on cars.

This floor was made stronger to prevent vibration and rust and will fit any Rod change gear shift mini started on the first injection cars

Right hand inner wing section only for MK3 cars with 3 air vent holes. One with 4 bolt holes,one with 4 castellated bolt holes (nuts welded in place) and one large trunk hose hole at front. If you want the same panel with A panel combined for better ...

This late front (nose) panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once! Early Minis can use [l...

This reinforcement for the bonnet platform panel was fitted to Cooper S models at an angle to enable fitment of oil cooler from 1966 on. Originally these were riveted by 2 pop rivets either end for all MK1 Cooper S. Painted black they were even found...