($47.25) £47.25 exc vat
($56.70) £56.70 inc vat
In stock
This is the regular 12G103 thermostat housing with the part number stamped on top as fitted to many minis but has a flanged front with extra material to allow drilling of a M10 hole.
($47.25) £47.25 exc vat
($56.70) £56.70 inc vat
In stockRecommended usage 1 x PEQ10010 to fit one mini.
MAQ10008 same part number.Fitted to 1275cc carb type engines from 1992 to 1994.
Has 2 vacuum pipes conected to it.
Screws into thermostat housing under top rad hose.
Use with special washer MAW10001.
...
Forget all the universal shape gaskets available - this is the original correct shape made out of thick gasket paper.
Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.
We have no evidence as yet that they last longer but do look good.
See [lin...
New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the valves and easier to control spring heights.
Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.
We have no evidence as yet that they last longer but do look good.
See [lin...
Originally marketed by minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment they were improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. These T b...
Originally marketed by Minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment. These have been improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. Ki...
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
New colour, PB104 bronze guides.Although Silicon bronze valve guides were used for their extremely good wear values, they were very hard and not user friendly when fitting. These valve guides are recommended when using all EN21 4N stainless steel val...
Use this plate in place of the heater valve. For use any time the heater is removed!
Great looking and fits all A-Series models! Bolting on an aluminium valve cover is the age-old way to dress up the engine compartment on any car! This finned aluminium valve cover utilizes the classic flat-top "Westlake" design. Painted aluminium val...
Rocker shafts wear fairly quickly. The upside to this used to be that the rocker bushes lasted longer, but later sintered rockers run without bushes. It is easier and less expensive to replace the rocker shaft!
Fits all models but beware as ...
That tell tale puff of blue smoke when you first start is an indicator of worn guides or seals. Valve guides should be replaced with every valve job.
Sold individually, these are the original quality Cooper S guides for use in any head espec...
Standard alloy thermostat housing. If you want the larger bore type as used on the Cooper with a sandwich plate see PEQ10019 housing GRH1140.
Requires thermostat gasket GTG101MS or GUG705558G...
This is the longer type cylinder head adaptor tube which allows fitment of the by pass hose without removing the head. The shortened hose GZA2083 slides up the tube and then back down on the water pump tube. Frequently rusted on old head...
Original Vented oil filler cap that should be change every 12 thousand miles.
The original flat cap type without breather filter on early minis has now been deleted by Rover and replaced by this filter type.
Thermal transmitter fitted in the cylinder head from 1970 on until its demise on the 1990 Coopers this part was the same as GTR143. One number was original fitment and the other supplied as the spare part by Unipart.
Fits 998 1275 and cooper...
As an engine wears, the clearance between the valve stem and guide increases; as this gets beyond tolerances the car will tend to smoke under deceleration (when you take your foot off the throttle). Good valve stem seals will allow for greater wear b...
Coolant temprature transmitter fitted to SPi cars from 1992 until 1996. This transmitter is denoted by it's black plastic end. Mounted to the underside of the inlet manifold.
MPI SANDWICH PLATE. No hole for radiator bracket although same caasting as other sandwich plates but has a large 12mm threaded hole in the side for the transmitter.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.