£2.80 exc vat
£3.36 inc vat
In stock
£2.80 exc vat
£3.36 inc vat
In stockRecommended usage 1 x 2A180 to fit one mini.
Heater valve studs fitted to the cylinder head. 1/4"unf 1.1250" long.
This gasket fits on the cylinder head for every A series heater valve or outlet pipe until the hole was no longer drilled when they changed to a heater valve fitted into the hose line from 1990 on.
New competition valve cotter for early heads with the large single groove valve, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the v...
Spring seat shims (set of 4), 0.020" thick (0.5mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT...
Fitting kit comprising of studs, nuts, plain washers, spring washers and a gasket
New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the valves and easier to control spring heights.
Set of strong lightweight titanium top caps to suit our valve springs C-AEA526/527 hard for single collet competition valves. Sold as a set of 8.
Alloy CNC version of the cylinder head take off 12G2534. The standard item being steel can be prone to corrosion, this CNC alloy version is smart, and will not corrode like steel does
Originally fitted to Minifin rocker covers as standard Rover equipment, it will also fit almost every other rocker cover including our FP26 range and Minispares alloy covers. This improved cap has a large grip and an improved lock system...
Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.
We have no evidence as yet that they last longer but do look good.
See [lin...
Spacers for under the rocker pedestals are used mainly by engine tuners to allow tappet adjustment to be made where cylinder head mods have been carried out. 1.3mm/0.0512" thick, this can be used to hold locating screw on rocker post assembly but the...
Early Large cotter groove exhaust valve. Most small bore engines seem particularly prone to burning valves, it is highly recommended to replace the exhaust valves when you do a valve job! This 1.0" valve fits most early 948cc, 998cc and 1098cc engine...
Unlike polished covers, these black powder coated aluminum valve covers don't get that dingy look; simply wipe them and they're clean. (Fins and Mini Spares logo remain cast aluminum finish) And they're made to clear our hi-lift rockers. Available ...
Originally marketed by minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment they were improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. These T b...
Originally marketed by Minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment. These have been improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. Ki...
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
New colour, PB104 bronze guides.Although Silicon bronze valve guides were used for their extremely good wear values, they were very hard and not user friendly when fitting. These valve guides are recommended when using all EN21 4N stainless steel val...
Genuine Mini Spares product as everything else on the market was poor fitting and unstable.
For Performance see 88G459EVO made in the USA by a Specialised Racing product company.
All the earlier heads used the 2A11 cott...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.