850cc Mini & 997cc Cooper Block
Label Part No Description Quantity Comments
1 12A1626 Connecting rod no. 2 and 4 2 N.L.A
2 12A1627 Connecting rod no. 1 and 3 2 N.L.A
3 51K1382 Small end bolt 4
4 2A660 Locktab for con rod bolt 4
5 12G2217 Big end bolt 8
6 8G2734 Crankshaft 11/2” diameter tail size (12A670 forging) 850cc 1 N.L.A - Deva bush type was 12A670
6 12A298 Crankshaft 11/2” diameter tail size (12A298 forging) 997cc 1 N.L.A
6 22A62 Crankshaft oil fed Early 850cc 1 N.L.A
7 6K836 Crankshaft key 1
8 VP572-00 Con rod bearing set (Mahle) 1 Std/10/20 only. Mahle was Vandervell
8 AEB572-00 Con rod bearing set (ACL) 1 Std/10/20/30/40 oversize
9 VP592 Mains bearing set journal width 1.185” 30.10mm Early 850cc 1 N.L.A
9 VP733-00 Mains bearing set journal width 1.064” 27.05mm 850/997cc 1 Std/10/20 only. Mahle was Vandervell
9 AEM3314-00 Mains bearing set journal width 1.064” 27.05mm 850/997cc 1 Std/10/20/30/40 oversize ACL
10 VPW95190 Thrust washer set was VPW94 850cc 1 C.W.E Std only
10 AEW2122-00 Thrust washer set 997cc 1 Std/3 thou oversize
11 22A1493 Primary gear(Deva) only fits 11/2” diameter crank tail only 1 Not early 850 1.375”
12 DAM8887 Bush front for cranks with 11/2” diameter 1 Was 22G401
12 22A451 Thrust washer 3.04-3.09mm (.120-122”) 1 These shims are used to give the correct end float of 3-6 thou on the primary gear, check 22A319 and 88G549 for wear.
13 22G109 Bush rear for cranks with 11/2” diameter 1
14 22A321 Thrust washers 2.79-2.84mm (.110-112”) - N.L.A 1 These shims are used to give the correct end float of 3-6 thou on the primary gear, check 22A319 and 88G549 for wear.
14 22A322 Thrust washers 2.84-2.89mm (.112-114”) 1 These shims are used to give the correct end float of 3-6 thou on the primary gear, check 22A319 and 88G549 for wear.
14 22A323 Thrust washers 2.89-2.94mm (.114-116”) 1 These shims are used to give the correct end float of 3-6 thou on the primary gear, check 22A319 and 88G549 for wear.
14 22A324 Thrust washers 2.94-2.99mm (.116-118”) 1 These shims are used to give the correct end float of 3-6 thou on the primary gear, check 22A319 and 88G549 for wear.
14 22A450 Thrust washers 2.99-3.04mm (.118-120”) 1 These shims are used to give the correct end float of 3-6 thou on the primary gear, check 22A319 and 88G549 for wear.
15 22A319 U Clip thrust washer 1
16 88G549 Backing ring 1
17 8G712 Camshaft 850cc Pin Drive. (Auto star drive 12A1065) 1 N.L.A
17 88G229 Camshaft (was 2A948) 997cc Pin drive 1 N.L.A
17 CAM6267 Camshaft 850cc Slot Drive A Plus 1 N.L.A
18 WKN505 Key 1
19 AHU2379 Camshaft plate was 2A84 1
20 GFK5179 Locating plate bolt 3
21 GHF321 Locating bolt shake-proof washer 3
22 2A85 Camshaft gear with tensioners 1 N.L.A- Use 12G4337 or duplex
23 8G549 Tensioner rubber rings 2
24 6K629 Camshaft nut 1
25 2A759 Locktab 1
26 8G725 Crankshaft gear 1
27 3H2127 Timing chain 1
28 2A970 Front plate 1 N.L.A
29 12G619B Gasket 1 For gasket sets see page 28
30 GFK5184 Screw, plate to block 2
31 GFK1125 Washer 2
32 53K2016 Screw plate to maincap 2
33 GHF321 Washer 1/4”star type 2 Was WF600041 (Landrover part)
34 12G4499 Distributor drive spindle 1 C.W.E
35 13H2792 “O” Ring distributor housing 1
36 12A1136 Distributor housing 1 N.L.A
37 2A14 Push rod 8 See C-AEG581 alternative
38 2A13 Cam follower less oil hole 8 Alternative to AEG584
38 AEG584 Cam follower with oil hole 8 Alternative to 2A13