£18.30 exc vat
£21.96 inc vat
In stock
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thinner tail crankshaft and different primary gear.
£18.30 exc vat
£21.96 inc vat
In stockRecommended usage 1 x 22A450 to fit one mini.
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thin...
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thi...
Genuine Churchill tool made for Rover to line up the clutch end case that holds the plunger and clutch arm, not many people ever thought they needed a tool for this but its the true way of lining up the case to centralise the clutch bearing to stop w...
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thi...
Replacement bolts for securing the DAM5921 to the AP verto clutch unit only. 6 required but sold individually.
Torque figure should be 40-45lbft not to be confused with the pressure plate to flywheel bolts which are 18lbft.
Upgraded Centre boss for all verto clutch/flywheel.
Fixing bolts are DAM5920 which are supplied in many clutch kits.
Race quality bolt-sold seperately- these shorter bolts hold the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.
Only tighten up to 16lbs per sq foot torque when using shake proof wa...
Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with C-2A3659 race ...
Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}
Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.
Heavy duty clutch release bearing with a wider surface area, helps to spread even pressure on the clutch diaphragm and is favoured by racers.
small face with numbers stamp-face outwards, larger surface aera side face flywheel.
This Verto type clutch arm is 2.75" long from the clevis pin hole.The earlier type pre verto is over 6"(165mm)long. the ball wears on both types and if the clutch is wrongly adjusted the arm (mainly the long type) can bend by way of hydraulic pressur...
Delete the metal pipe and existing hose by fitting this longer one piece steel braided pipe which can be used for either early or verto clutches. A sensible modification for all mini owners.
Clutch diaphragm, blue for 1275/1100/998/850 Mini, pre Verto.
This part superseded the GCC102 850-1100 diaphragm.
There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.
Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.