£18.00 exc vat
£21.60 inc vat
In stock
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thinner tail crankshaft and different primary gear. Regret 22A321 and 22A323 are the only size available now from Rover and sometimes only available to customer order as sales are nearly non existent.
£18.00 exc vat
£21.60 inc vat
In stockRecommended usage 1 x 22A324 to fit one mini.
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Extra strong magnetic sump plug. This high quality plug is constructed from 303 stainless steel and houses the latest Neodymium magnet which is currently the strongest available to give the best protection for your engine, even more important when yo...
Fully floating primary gear bush to downsize from our 1275cc type to 998 size on our 1275 primary gears with circlip conversion only to fit small bore crankshafts. Mainly used for our straight cut primary gear with circlip to hold fully floating bush...
Short diff housing bolt fitted to Rod change gearbox only 3/8"unc and 2.25"long. For the 2 long STUDS useTAM1617. £0.34 exc vat £0.41 inc vat
For use on Diff housing
Remote type case
53K266 are 4.5" long -4 for remote now use
Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.
This is a special rigid seal and ...
FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)
housing and deleted 1996 on.locking glue used such as locktite
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
The plastic bush at the base of the gear lever stalk ON REMOTE TYPE GEARBOXES ONLY--stops that rattling noise
fit to the gearlever, not the knuckle joint, if it falls of the gear lever there will be a lot of play
59 tooth crownwheel plus 20 tooth pinion making 2.95 ratio. A plus gears sold as a set only.
Genuine Mini Spares product, fits 3 and 4-synchro gearboxes except for rod change types which use GAE191. This switch replaces the plug on the front of the remote-shift transmission case. It is triggered internally by the shift linkage w...
Genuine Mini Spares product, 2nd gear 4 synchro Pre A Plus-26 teeth
If you are about to undertake a gearbox strip down and you are using an old Haynes manual beware. When locking the gearbox into 2 gears to undo the large mainshaft and Ist m...
Primary gear thrust washers are made in varying sizes to take up the play.
Standard gap size should be between 3-6 thou. These are for the 850/998/1098cc
engines with 22A1493 Deva bush primary gear. Early 850cc had thin...
3 of these bolt are used on the speedo housing gearbox front cover-they used to be 53K1474 studs 3.75" long but change to this bolt in 1985 3.25"long 5/16"unc
with tuflock patch to secure.
