£1.80 exc vat
£2.16 inc vat
In stock
£1.80 exc vat
£2.16 inc vat
In stockRecommended usage 2 x BTA102 to fit one mini.
Genuine Rover are now 48 thou thick which is so tight they can lock up your differential. The originals were .035 thou. These are machined down to be exactly the correct size required but we also stock oversize 43 thou type which are available as [li...
Hardy Spicer Adapters to convert pot joint output shafts to fit a hardy spice coupling (will also fit the Quaife ATB)
The Swiftune classic Mini Quaife ATB Automatic Torque Biasing differential offers the benefits of an LSD limited slip differential but saving you money on crownwheels and pinion plus output shafts!!
The Swiftune Quaife ATB avoids the need fo...
Fits all minis except Autos and those with hardy spicer joints. It has the detent lug on for rod change R/H side. Sold singly.
These might be marked as 22G420 on the casting but they have the correct size bush and seal hole for...
"USED" secondhand crownwheel and pinion 3.647 ratio "A" plus teeth. 17x62 teeth
Sold as seen,some with inner part of bearing still on crownwheel (if they come off without using a puller tool it usually means they have spun, ruining the seati...
New Minispares Evolution straight cut crownwheel and pinion set 3.75. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from aero quality steel making it 20% tougher.16x60 teeth count.
Always Check...
New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17/59 teeth cont
Not for LSD se...
61 tooth crownwheel and 19 tooth pinion (pinion is also used on 3-1 final drive)
A plus gears giving 3.211 ratio.
A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105
59 tooth crownwheel plus 20 tooth pinion making 2.95 ratio. A plus gears sold as a set only.
Crownwheel with 58 teeth and pinion gear with 21 teeth. Not supplied with bearings.
Hardened flat washer to be used with flange type LSD Hardy Spicer C-BTA1262 outputs.
Minispares own Evolution limited slip diff with over 10 years success General spec and design is the same as C-AJJ3387 but has a 55/90 ramp type. The steeper 55 degree acceleration ramp reduces the percentage of torque biased to the ...
Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.
these...
IF YOU EVER STRIP ONE OF OUR C-AJJ3385 CROSSPIN DIFFS DOWN THIS IS THE LONG MOLYBDENUM COATED PIN THAT THE PLANET WHEELS RUN ON.
IF YOU EVER STRIP ONE OF OUR C-AJJ3385 CROSSPIN DIFFS DOWN THIS IS THE SHORTMOLYBDENUM COATED PIN THAT A PLANET WHEEL RUNS ON.
USED pairing 64 tooth crownwheel and a 17 tooth pinion for 3.76 original mini final drive ratio of 3.76
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.