£2.70 exc vat
£3.24 inc vat
In stock
£2.70 exc vat
£3.24 inc vat
In stockRecommended usage 2 x DAM5071 to fit one mini.
Standard replacement precision ground upgraded material standard diff pin. Recommended for all standard differential rebuilds. For performance, use C-BTA164 moly coated pin with standard planet gears. Pay special attention to the conditi...
Competition quality replacement diff pin with anti wear MOLYBDENUM coating for planet wheel surfaces and still cheaper than a standard Rover pin. Recommended for all differential rebuilds.Pay special attention to the condition of the planet wheels wh...
Genuine Rover Tuftrided diff pin, as fiited to all the later A+ gearboxes as a standard upgrade. These are the last genuine parts left and will not be available again
Genuine Rover are now 48 thou thick which is so tight they can lock up your differential. The originals were .035 thou. These are machined down to be exactly the correct size required but we also stock oversize 43 thou type which are available as [li...
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
On certain motorsport events which include vigorous stopping and starting it is possible that the diff pin will wear badly or even break,this is due to the uneven load applied by the varying tolerances and poor machining of the planet gears.This kit ...
Minispares centre own reconditioned helical gearbox with all new ball bearings
throughout except under 1st, 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc.3.1 diff fitted. ...
Mini Spares Close ratio Evolution five speed "A" Plus Rod-change helical cut teeth gearbox has been in production since 1993 with phenomenal proven reliability. Do not use a quick shift gear lever with this gearbox
Suitable for 1275-1380cc(e...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.2.9-1 diff fitted .any fa...
Full rebuild kit with diferential parts with standard layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 1st, 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc.3.2 diff fitted .an...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 1st,2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.3.4 diff fitted .any ...
Full rebuild kit with differential parts and standard layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full...
Full rebuild kit with diferential parts with competition layshaft, our 22G2033EVO baulk rings and performance clutch oil seal 13H2934MS
Using only the original manufacturers of the bearings such as RHP because all t...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 1st,2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.3.1 diff fitted. Any ...
This gearbox is identical to MSG04 except for a 3.2 final drive which effectively gives you a final drive ratio of 2.822 in 5th.
Does not come with input gear supplied.
Mini Spares 'Straight Cut Close Ratio 4-Speed gearboxes'
Mini Spares are proud to offer a new range of straight cut, 4-speed rod change gearboxes.
These gearboxes undergo a full rebuild, using new; bearings, sea...
Mini Spares 'Straight Cut Close Ratio 4-Speed gearboxes'
Mini Spares are proud to offer a new range of straight cut, 4-speed rod change gearboxes.
These gearboxes undergo a full rebuild, using new; bearings, sea...
Reconditioned and rebuilt differential assembly for use with Pot joints
Differential housing, 1 output shaft and centre block are bead blasted, new planet gears are installed along with new casing bushes, roll pins and an uprated d...
Minispares centre own reconditioned helical gearbox with all new ball bearings
throughout except under 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc. 2.7-1 diff fitted as ...
Mini Spares 'Straight Cut Close Ratio 4-Speed gearboxes'
Mini Spares are proud to offer a new range of straight cut, 4-speed rod change gearboxes.
These gearboxes undergo a full rebuild, using new; bearings, sea...
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 1st,2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.3.4 diff fitted .any ...
This gearbox is identical to MSG04 except for a 3.1 final drive which effectively gives you a final drive ratio of 2.73 in 5th.
Do not come with input gear supplied.
Minispares centre own reconditioned helical tranny with all new ball bearings
throughout except under 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc. 2.7-1 diff fitted as p...
Close ratio 4 speed helical gearbox using our C-STN48 gear kit.
1st gear ratio 2.583
2nd gear 1.644
3rd gera 1.250
Hardened flat washer to be used with flange type LSD Hardy Spicer C-BTA1262 outputs.
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
These are the larger bore diff side covers when hardy spicers are fitted and they also have the flange to cover detent spring on side if fitted to rod change when converted to hardy spicer. Has a 50mm oil seal o/d and bush size 34.8mm.For the yoke o...
A bronze type bush that fits in the gearbox output shaft side cover on early automatics and Cooper S with hardy spicer type joints. These are larger than the standard mini or rod change engine gearbox types which take 2A3538.
Planet gears for the differential are now manufactured by us as the genuine Rover product is obsolete. Beware of others on the market which must be checked before fitting as the overall dimensions in height seem to vary along with inferior/wrong mate...
This is an aftermarket high tensile shouldered bolt that engine and gearbox tuners are using, as the original shape head and high tensile type bolt is no longer available. For holding the crown wheel to the differential housing.
Sold individ...
Fits all minis except Autos and those with hardy spicer joints, has no lug on as required for rod change L/H side. Sold singly.
The Mini transmission output side cover is notorious for leaking oil, but replacing the seal doesn't help for lon...
Circlip that fits on the gearbox output shaft in the differential for the pot joint type cars. Sold singly 2 required per gearbox.
Bronze type bush is in the centre of all crownwheels in the gearbox plus another one is in the differential case opposite the end the crownwheel fits.
The bush after fitting will need to be reamed. Ream to 26.16mm 1.03"
Competition quality replacement diff pin with anti wear MOLYBDENUM coating for planet wheel surfaces and still cheaper than a standard Rover pin. Recommended for all differential rebuilds.Pay special attention to the condition of the planet wheels wh...
Standard replacement precision ground upgraded material standard diff pin. Recommended for all standard differential rebuilds. For performance, use C-BTA164 moly coated pin with standard planet gears. Pay special attention to the conditi...
Outputs for LSD when using inboard CV joints. Sold single with 2 needed per car.
The Swiftune classic Mini Quaife ATB Automatic Torque Biasing differential offers the benefits of an LSD limited slip differential but saving you money on crownwheels and pinion plus output shafts!!
The Swiftune Quaife ATB avoids the need fo...
"USED" secondhand crownwheel and pinion 3.647 ratio "A" plus teeth. 17x62 teeth
Sold as seen,some with inner part of bearing still on crownwheel (if they come off without using a puller tool it usually means they have spun, ruining the seati...
New Minispares Evolution straight cut crownwheel and pinion set 3.75. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from aero quality steel making it 20% tougher.16x60 teeth count.
Always Check...
New Minispares Evolution straight cut crownwheel and pinion set 3.875. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.16x62 teeth count
New Minispares Evolution straight cut crownwheel and pinion set 3.75. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.16x60 teeth count.
THIS IS THE ...
New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17/59 teeth cont
Not for LSD se...
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.