£62.72 exc vat
£75.26 inc vat
In stock
£62.72 exc vat
£75.26 inc vat
In stockRecommended usage 1 x C-BTA167 to fit one mini.
Standard replacement precision ground upgraded material standard diff pin. Recommended for all standard differential rebuilds. For performance, use C-BTA164 moly coated pin with standard planet gears. Pay special attention to the conditi...
The latest model Mini differential still use thrust washers on the spider gears but now have a tab on one end to prevent them from rotating on the cage side of the diff. The cage of course is cast while the gear itself is much harder and thus the wh...
Special pin to hold the differential cross pin in place in the housing.
Fits all minis except Autos and those with hardy spicer joints. It has the detent lug on for rod change R/H side. Sold singly.
These might be marked as 22G420 on the casting but they have the correct size bush and seal hole for...
"USED" secondhand crownwheel and pinion 3.647 ratio "A" plus teeth. 17x62 teeth
Sold as seen,some with inner part of bearing still on crownwheel (if they come off without using a puller tool it usually means they have spun, ruining the seati...
Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...
61 tooth crownwheel and 19 tooth pinion (pinion is also used on 3-1 final drive)
A plus gears giving 3.211 ratio.
A plus crownwheel and pinion with 59 teeth and 19 teeth respectively=3.105
59 tooth crownwheel plus 20 tooth pinion making 2.95 ratio. A plus gears sold as a set only.
Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.
these...
Genuine RHP as originally fitted to every production Mini.
Two of these main diff carrying bearings are required in the gearbox and this new steel caged type fits either way round. Should be pre loaded by 1-2 thou.
Some original fi...
The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.
Hardy-Spicer coupling was fitted to the Cooper "S" and all automatic varieties pre Pot joint(inboard cv joint) This U-joint assembly slides onto the driveshaft and bolts to the Cooper S output shaft flange. The U joint fitted to these joints is the s...
These are the larger bore diff side covers when hardy spicers are fitted and they also have the flange to cover detent spring on side if fitted to rod change when converted to hardy spicer. Has a 50mm oil seal o/d and bush size 34.8mm.For the yoke o...
Only fitted to vehicles with hardy spicer output shafts (Cooper S and autos). Two collets are fitted in the output shaft in the gearbox and located behind the rubber seal 22A1566
A bronze type bush that fits in the gearbox output shaft side cover on early automatics and Cooper S with hardy spicer type joints. These are larger than the standard mini or rod change engine gearbox types which take 2A3538.
Stronger PRE a PLUS with 62 tooth crownwheel plus the 18 tooth pinion making a 3.444 diff ratio as used on Cooper S, plus many 998cc cars from 1970 on.
This is the original Evolution"Cross-pin" differential for the Mini.
Produced and sold by Mini Spares since 1994. It is a super heavy duty differential designed as a significant upgrade for reliability and strength to the standard units. Ove...
Planet gears for the differential are now manufactured by us as the genuine Rover product is obsolete. Beware of others on the market which must be checked before fitting as the overall dimensions in height seem to vary along with inferior/wrong mate...
The gearbox diff side plate bonze colour bush for all except auto and cooper S with hardy spicer output shafts. Sold singly 2 required per gearbox.
clearance needs to be 0.03mm
This is an aftermarket high tensile shouldered bolt that engine and gearbox tuners are using, as the original shape head and high tensile type bolt is no longer available. For holding the crown wheel to the differential housing.
Sold individ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.