DIFFERENTIAL FIBRE THRUST WASHER STANDARD SIZE
BTA101

£1.80 exc vat

£2.16 inc vat

In stockIn stock
Genuine Rover are now 48 thou thick which is so tight they can lock up your differential. The originals were .035 thou. These are machined down to be exactly the correct size required but we also stock oversize 43 thou type which are available as BTA102 for worn units. We have never required anything larger that was servicable. Sold singly and 2 required per gearbox.

£1.80 exc vat

£2.16 inc vat

In stockIn stock

Recommended usage 2 x BTA101 to fit one mini.
Differential - Qty 2
Differential Assembly - Qty 2

Recommended products

The latest model Mini differential still use thrust washers on the spider gears but now have a tab on one end to prevent them from rotating on the cage side of the diff. The cage of course is cast while the gear itself is much harder and thus the wh...

The bronze washer for the planet gears in the differential for pre A plus gearbxes. You can use the DAM5071 and cut the lips off.

Alternative products

Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...

Kit products

Minispares centre own reconditioned helical gearbox with all new ball bearings

throughout except under 1st, 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc.3.1 diff fitted. ...

Mini Spares Close ratio Evolution five speed "A" Plus Rod-change helical cut teeth gearbox has been in production since 1993 with phenomenal proven reliability. Do not use a quick shift gear lever with this gearbox

Suitable for 1275-1380cc(e...

Minispares centre own reconditioned helical tranny with all new ball bearings

throughout except under 2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.2.9-1 diff fitted .any fa...

Full rebuild kit with diferential parts with standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Full rebuild kit with diferential parts with competition layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a f...

Minispares centre own reconditioned helical tranny with all new ball bearings

throughout except under 1st, 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc.3.2 diff fitted .an...

Minispares centre own reconditioned helical tranny with all new ball bearings

throughout except under 1st,2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.3.4 diff fitted .any ...

Full rebuild kit with dihferential parts and standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Full rebuild kit with differential parts and standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Full rebuild kit with diferential parts with competition layshaft, our 22G2033EVO baulk rings and performance clutch oil seal 13H2934MS

Using only the original manufacturers of the bearings such as RHP because all t...

This gearbox is identical to MSG04 except for a 3.2 final drive which effectively gives you a final drive ratio of 2.822 in 5th.

Does not come with input gear supplied.

Reconditioned and rebuilt differential assembly for use with Pot joints



Differential housing, 1 output shaft and centre block are bead blasted, new planet gears are installed along with new casing bushes, roll pins and an uprated d...

Minispares centre own reconditioned helical gearbox with all new ball bearings

throughout except under 2/3rd gear which are usually okay and very expensive, performance layshaft, special oil pick up pipe, diff pin etc. 2.7-1 diff fitted as ...

Minispares centre own reconditioned helical tranny with all new ball bearings

throughout except under 1st,2/3rd gear which are usually okay and very expensive, performance layshaft,special oil pick up pipe,diff pin etc.3.4 diff fitted .any ...

This gearbox is identical to MSG04 except for a 3.1 final drive which effectively gives you a final drive ratio of 2.73 in 5th.

Do not come with input gear supplied.

People also bought products

High quality version of 13H9513, INA branded.



Dual use bearing fits the end of the A Plus 18mm mainshaft where the 1st Motion shaft slides on, plus it is used on the A Plus layshaft smaller end.



Kno...

IKO idler gear bearing with special rollers for allowing movement on late type idler gears. The idler gears for twin point cars were also made from clean steel as an upgrade from 1996 on. This special bearing replaces the cheaper inferior earlier bea...

Hardy Spicer Adapters to convert pot joint output shafts to fit a hardy spice coupling (will also fit the Quaife ATB)

The Swiftune classic Mini Quaife ATB Automatic Torque Biasing differential offers the benefits of an LSD limited slip differential but saving you money on crownwheels and pinion plus output shafts!!

The Swiftune Quaife ATB avoids the need fo...

Fits all minis except Autos and those with hardy spicer joints. It has the detent lug on for rod change R/H side. Sold singly.

These might be marked as 22G420 on the casting but they have the correct size bush and seal hole for...

Genuine Rover spacer that fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear.

Mini Spares also produce a ring 2 thou thicker 88G549 to...

Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962

Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.

5/16"unc stud 3.75"long for speedo housing case and uses unf the nut end. The washers are GFK1114 and the nuts GFK3212.

These are for the speedo housing case and sold individually but 3 required.

FITTED from 1984 on-single locktab for the 3 bolt main bearing(double roller)

housing and deleted 1996 on.locking glue used such as locktite

"USED" secondhand crownwheel and pinion 3.647 ratio "A" plus teeth. 17x62 teeth

Sold as seen,some with inner part of bearing still on crownwheel (if they come off without using a puller tool it usually means they have spun, ruining the seati...

New Minispares Evolution straight cut crownwheel and pinion set 3.875. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.16x62 teeth count

Always Check...

New Minispares Evolution straight cut crownwheel and pinion set 3.75. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from aero quality steel making it 20% tougher.16x60 teeth count.

Always Check...

New Minispares Evolution straight cut crownwheel and pinion set 3.875. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.16x62 teeth count

New Minispares Evolution straight cut crownwheel and pinion set 3.75. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.16x60 teeth count.

THIS IS THE ...

New Minispares Evolution straight cut crownwheel and pinion set 3.47. The crownwheel in these kits has a 20% wider gear than previously supplied, and a pinion made from Aero quality steel making it 20% tougher.17/59 teeth cont

Not for LSD se...

Genuine Rover fibre type are now 48 thou thick which is so tight it will probably lock your diff up, they used to originally be .035 thou. These are 43 thou oversize type for worn units but the correct size of 35 thou is available as BTA101<...

Solid dowel at the front of the engine that locates the block to gearbox.

61 tooth crownwheel and 19 tooth pinion (pinion is also used on 3-1 final drive)

A plus gears giving 3.211 ratio.